5.4BQB测试报告222830-20241125（7/8）

📎 原始文档：https://www.kdocs.cn/l/cpCfdlw9wnJV

Item	Capability	Reference	Support	Comment
1/1	Power Class 1	[1] 3	C.5	C.5: Mandatoryto support at least one of RF 1/1 "Power Class 1" OR RF 1/2 "Power Class 2" OR RF 1/3 "Power Class 3".
1/4	Power Control	[1] 3	C.1	C.1: Mandatory IF RF 1/1 "Power Class 1", otherwise Optional IF RF 1/2 "Power Class 2" OR RF 1/3 "Power Class 3", otherwise Excluded.
1/5	1-slot packets supported	[2] 6.5	M
1/6	3-slot packets supported	[2] 6.5	O
1/7	5-slot packets supported	[2] 6.5	O
1/8	79 Channels	[1] 2	M
1/9	Support for GFSK modulation	[1] 3.1	M
1/10	Support for p/4-DQPSK modulation	[1] 3.2	C.2	C.2: Mandatory IF SUMICS 22/1 "EDR for asynchronous transports (single slot)" OR SUMICS 22/2 "EDR for asynchronous transports (multi-slot)" OR SUM ICS 22/4 "EDR for synchronous transports (Core 3 .0 or later)", otherwise Excluded.
1/11	Support for 8DPSK modulation	[1] 3.2	C.3	C.3: Mandatory IF SUMICS 22/1 "EDR for asynchronous transports (single slot)" OR SUMICS 22/2 "EDR for asynchronous transports (multi-slot)", otherwise Optional IF SUM ICS 22/4 "EDR for synchronous transports (Core 3 .0 or later)", otherwise Excluded.
1/12	Enhanced Power Control	[1] 3	C.4	C.4: Optional IF RF 1/4 "Power Control", otherwise Excluded.

RFCOMM

Table 0: Major Versions (X.Y)

Item	Capability	Reference	Support Status	Comment
0/2	RFCOMMv1 2 with	[1]		C.1: Mandatoryto support one and onlyone of RFCOMM0/1 "RFCOMMv1 .1 with TS 07.10" OR
	TS07 10			RFCOMM0/2 "RFCOMMv1 2 with TS07 10"

C.1

Table 1: Supported Procedures

1/1	Initialize RFCOMMSession	[1] 5.2.1	C.5	C.5: Mandatoryto support at least one of RFCOMM1/1 "Initialize RFCOMMSession" ORRFCOMM1/2 "Respond to Initialization of an RFCOMMSession".
1/2	Respond to Initialization of an	[1] 5.2.1	C.5	C 5: Mandatoryto support at least one of RFCOMM1/1 "Initialize RFCOMMSession" OR
	RFCOMMSession			RFCOMM1/2 "Respond to Initialization of an RFCOMMSession".
1/3	Shutdown RFCOMMSession	[1] 5.2.2	M
1/4	Respond to a Shutdown of an RFCOMMSession	[1] 5.2.2	M
1/5	Establish DLC	[1] 5.2.1	C.2	vi C.2: Mandatory IF RFCOMM1/1 "Initialize RFCOMMSession", otherwise Excluded.
1/6	Respond to Establishment of a	[1] 5.2.1	C.1	C 1: Mandator IF RFCOMM1/2 "Res ond to Initialization of an RFCOMMSession"
	DLC			otherwise Excluded.
1/7	Disconnect DLC	[1] 5.2	M
1/8	Respond to Disconnection of a DLC	[1] 5.2	M
1/9	Respond to and send MSC Command	[1] 2.2	M
1/10	Initiate Transfer Information	[1] 5.1	M
1/11	Respond to Test Command	[1] 4.3	M
1/12	Send Test Command	[1] 4.3	O
1/13	React to Aggregate Flow Control	[1] 6.3	M
1/14	Respond to RLS Command	[1] 5.5.2	M
1/15	Send RLS Command	[1] 5.5.2	O
1/16	Respond to PN Command	[1] 5.5.3	M
1/17	Send PN Command	[1] 5.5.3	C.3	C.3: Mandatory IF RFCOMM1/1 "Initialize RFCOMMSession", otherwise Optional.
1/18	Send Non-Supported Command (NSC) response	[1] 4.3	C.4	C.4: Mandatory IF RFCOMM0/2 RFCOMMv1 .2 with TS 07.10 , otherwise Optional.
1/19	Respond to RPN Command	[1] 5.5.1	M
1/20	Send RPN Command	[1] 5.5.1	O
1/21	Closing Multiplexer by First Sending a DISC Command	[1] 5.2.2	O
1/22	Support of Credit Based Flow Control	[1] 6.5	M

.
.
y
p
,
"
"

Low Energy RF PHY

Table 1 : Bluetooth LE RF Capabilities

Item	Capability	Reference	Support	Comment
1/1	LE Transmitter	[1] 3	C.1	C.1: Mandatoryto support at least one of RFPHY 1/1 "LE Transmitter" OR RFPHY 1/2 "LE Receiver" OR RFPHY 1/3 "LE Transceiver". Note: Selecting both RFPHY 1/1 "LE Transmitter" and RFPHY 1/2 "LE Receiver" is equivalent to selecting RFPHY 1/3 "LE Transceiver" and vice versa.
1/2	LE Receiver	[1] 4	C.1	C.1: Mandatoryto support at least one of RFPHY 1/1 "LE Transmitter" OR RFPHY 1/2 "LE Receiver" OR RFPHY 1/3 "LE Transceiver". Note: Selecting both RFPHY 1/1 "LE Transmitter" and RFPHY 1/2 "LE Receiver" is equivalent to selecting RFPHY 1/3 "LE Transceiver" and vice versa.
1/3	LE Transceiver	[1] 3, 4	C.1	C.1: Mandatoryto support at least one of RFPHY 1/1 "LE Transmitter" OR RFPHY 1/2 "LE Receiver" OR RFPHY 1/3 "LE Transceiver". Note: Selecting both RFPHY 1/1 "LE Transmitter" and RFPHY 1/2 "LE Receiver" is equivalent to selecting RFPHY 1/3 "LE Transceiver" and vice versa.
1/4	LE2MPHY	[3] 3, 4	C 2	C 2: Excluded IF SUM ICS 21/14 "Core v4 .2", otherwise Optional.
1/5	Stable Modulation IndexTransmitter	[3] 3.1.1	C.3	C.3: Excluded IF SUM ICS 21/14 "Core v4 .2", otherwise Optional IF RFPHY 1/1 "LE Transmitter" OR RFPHY 1/3 "LE Transceiver", otherwise Excluded.
1/6	Stable Modulation Index-	[3] 3.1.1	C.4	C.4: Excluded IF SUM ICS 21/14 "Core v4 .2", otherwise Optional IF RFPHY 1/2 "LE
	Receiver			Receiver" OR RFPHY 1/3 "LE Transceiver", otherwise Excluded.
1/7	LE Coded PHY	[3] 3, 4	C 2	C 2: Excluded IF SUM ICS 21/14 "Core v4 .2", otherwise Optional.

1/8	Transmitting Constant Tone Extensions	[4] 5	C.10	C.10: Excluded IF SUMICS 21/14 "Core v4 .2" OR SUMICS 21/16 "Core v5 .0", otherwise Optional IF RFPHY 1/1 "LE Transmitter" OR RFPHY 1/3 "LE Transceiver", otherwise Excluded.
1/9	2 µs Antenna Switching During	[4] 5	C.5	C.5: Optional IF RFPHY 1/8 "Transmitting Constant Tone Extensions", otherwise
	Constant Tone Extension Transmission (AoD)			Excluded.
1/10	1 μs Antenna Switching During	[4] 5	C 6	C.6: Optional IF RFPHY 1/9 "2 μs Antenna Switching During Constant Tone Extension
	Constant Tone Extension Transmission (AoD)			Transmission (AoD)", otherwise Excluded.
1/11	2 μs Antenna Sampling During	[4] 5		C.11: Excluded IF SUMICS 21/14 "Core v4 .2" OR SUMICS 21/16 "Core v5 .0", otherwise
	Constant Tone Extension			Optional IF RFPHY 1/2 "LE Receiver" OR RFPHY 1/3 "LE Transceiver", otherwise
	Reception (AoD)			Excluded.
1/12	2 μs Antenna Switching and	[4] 5		C.7: Optional IF RFPHY 1/11 "2 μs Antenna Sampling During Constant Tone Extension
	Sampling During Constant Tone Extension Reception (AoA)			Reception (AoD)", otherwise Excluded.
1/13	1 μs Antenna Sampling During	[4] 5	C.7	C.7: Optional IF RFPHY 1/11 "2 μs Antenna Sampling During Constant Tone Extension
	Constant Tone Extension Reception (AoD)			Reception (AoD)", otherwise Excluded.
1/14	1 µs Antenna Switching and	[4] 5	C.8	C.8: Mandatory IF RFPHY 1/12 "2 μs Antenna Switching and Sampling During Constant
	Sampling During Constant Tone			Tone Extension Reception (AoA)" AND RFPHY 1/13 "1 μs Antenna Sampling During
	Extension Reception (AoA)			Constant Tone Extension Reception (AoD)", otherwise Excluded.

.
C.11
C.7

Table 2: Bluetooth LE Test Interface Capabilities

Item	Capability	Reference	Support Status	Comment
2/1	HCITest	[2] 2		C.1: Mandatoryto support at least one of RFPHY2/1 "HCITest Interface" OR RFPHY2/2 "UART Test
	Interface			Interface"

C.1

Service Discovery Protocol

Table 1b: Role Requirements

Item	Capability	Reference	Support	Status	Comment
1b/1	Server	[1] 2.1	C.1		C.1: Mandatoryto support at least one of SDP 1b/1 "Server" OR SDP 1b/2 "Client".
1b/2	Client	[1] 2.1	C.1		C.1: Mandatoryto support at least one of SDP 1b/1 "Server" OR SDP 1b/2 "Client".

Table 1: Support Different Size Capabilities on UUID

Prerequisite: SDP 1b/1 "Server"

Item	Capability	Reference	Support
1/1	128 bit UUID	[1] 2.5.1	M
1/2	32 bit UUID	[1] 2.5.1	M
1/3	16 bit UUID	[1] 2.5.1	M

Table 2: Service Search Request

Prerequisite: SDP 1b/1 "Server"

Item	Capability	Reference	Support	Status			Comment
2/1	Service Search Response	[1] 4.5 2	M

Table 3: Error Response to Invalid Service Search Request

Prerequisite: SDP 1b/1 "Server"

Item Capability Reference Support Status Comment
3/1 Error response to Service Search Request
Table 4: Service Attribute Request Prerequisite: SDP 1b/1 "Server"
Item Capability	Reference Support Status Comment

[1] 4.4 M

4/1	Service Attribute Response	[1] 4.6.2	M
4/2	Generates continuation state in Service Attribute Response	[1] 4.3, 4.6.2	O
4/3	Service Attribute Response with AdditionalProtocolDescriptorList attribute	[1] 4.5.2, 5.1.6	O

Table 5: Error Response to Invalid Service Attribute Request

Prerequisite: SDP 1b/1 "Server"

Item	Capability	Reference	Support	Status		Comment
5/1	Error response to Service Attribute Request	[1] 4.4	M

Table 6: Service Search Attribute Request

Prerequisite: SDP 1b/1 "Server"

Item	Capability	Reference	Support Status Comment
6/1	Service Search Attribute Response	[1] 4.7.2	M
6/2	Generates continuation state in Service Search Attribute Response	[1] 4.3, 4.7.2	O
6/3	Service Search Attribute Response with AdditionalProtocolDescriptorList attribute	[1] 4.7.2, 5.1.6	O

Table 7: Invalid Service Search Attribute Request

Prerequisite: SDP 1b/1 "Server"

Item	Capability	Reference	Support	Status		Comment
7/1	Error response to Service Search Attribute Request	[1] 4.4	M

Table 8: Service Browsing

Prerequisite: SDP 1b/1 "Server"

Item	Capability Reference	Support	Status	Comment
Table 9: Attributes Present in IUT Prerequisite: SDP 1b/1 "Server"
Item	Capability	Reference	Support	Status Comment
9/2	ProtocolDescriptorList	[1] 5.1.5	O
9/9	ServiceName	[1] 5.1.15	O
9/14	BluetoothProfileDescriptorList	[1] 5.1.11	O
9/18	ServiceRecordHandle	[1] 5.1.1	M
9/19	ServiceClassIDList	[1] 5.1 2	M

Security Manager Protocol

Table 1 : Role Requirements

Item	Capability	Reference	Support	Status	Comment
1/1	Central Role (Initiator)	[1] 2.4	C.1		C.1: Mandatoryto support at least one of SM 1/1 "Central Role (Initiator)" OR SM 1/2 "Peripheral Role (Responder)".
1/2	Peripheral Role (Responder)	[1] 2.4	C.1		C.1: Mandatoryto support at least one of SM 1/1 "Central Role (Initiator)" OR SM 1/2 "Peripheral Role (Responder)".

Table 2: Security Properties

Item	Capability	Reference	Support	Comment
2/1	Authenticated MITMprotection	[1] 2.3.1	O
2/2	Unauthenticated no MITMprotection	[1] 2.3.1	C.1	C.1: Mandatory IF SM2/1 "Authenticated MITMprotection", otherwise Optional.
2/3	No security requirements	[1] 2.3.1	M
2/5	LE Secure Connections	[2] 2.3.1	O

Table 3: Encryption Key Size
Prerequisite: SM 2/1 "Authenticated MITM protection" OR SM 2/2 "Unauthenticated no MITM protection" OR SM 2/4 "OOB supported"

Item	Capability	Reference	Support	Status			Comment
3/1	Encryption KeySize	[1] 2.3.4	M

Table 4: Pairing Method

Item Capability Reference Support Status Comment
4/1 Just [1] 2.3.5 O
Works
4/2 Passkey [1] 2.3.5 C.1 ~~ ~~ C.1: Mandatoryto support at least one of SM4/2 "Passkey Entry" OR SM4/3 "Out of Band" IF SM2/1 Entry "Authenticated MITMprotection", otherwise Excluded.

Table 5: Security Initiation

Item	Capability	Reference	Support	Comment
5/1	Encryption Setup using STK	[1] 2.4	C.3	C.3: Mandatory IF SM2/1 "Authenticated MITMprotection" OR SM2/2 "Unauthenticated no MITM protection" OR SM2/4 "OOB supported", otherwise Excluded.
5/2	Encryption Setup using LTK	[1] 2.4	O
5/3	Peripheral Initiated Security	[1] 2.4.6	C.1	C.1: Optional IF SM 1/2 "Peripheral Role (Responder)", otherwise Excluded.
5/4	Peripheral Initiated Security– Central response	[1] 2.4.6	C.2	C.2: Mandatory IF SM 1/1 "Central Role (Initiator)", otherwise Excluded.
5/5	CT2 bit	[3] 2.4.2.4, 3.5.2	C.4	C.4: Excluded IF NOT SM8a/1 "Cross Transport Key Derivation Supported" AND NOT SM8b/1 "Cross Transport Key Derivation Supported", otherwise Mandatory IF NOT SUMICS 31/17 "Core v4 2" AND NOT SUMICS 31/18 "Core v4 2+HS", otherwise Optional

Table 6: Signing Algorithm

Item	Capability	Reference	Support	Status	Comment
6/1	Signing Algorithm-Generation	[1] 2.4	O
6/2	Signing Algorithm-Resolving	[1] 2.4	O

Table 7a: Key Distribution by Central

Prerequisite: SM 1/1 "Central Role (Initiator)"

Item	Capability	Reference	Support
7a/1	Encryption Key	[1] 2.4.3	O
7a/2	Identity Key	[1] 2.4.3	O
7a/3	Signing Key	[1] 2.4.3	O

Table 7b: Key Distribution by Peripheral

Prerequisite: SM 1/2 "Peripheral Role ( Responder)"

Item	Capability	Reference	Support
7b/1	Encryption Key	[1] 2.4.3	O
7b/2	Identity Key	[1] 2.4.3	O
7b/3	Signing Key	[1] 2.4.3	O

Table 8a: Cross-Transport Key Derivation by Central

Prerequisite: SM 1/1 "Central Role (Initiator)"

8a/1	Cross Transport Key Derivation Supported	[1] 2.3.5.7	C.1	C.1: Optional IF SM2/5 "LE Secure Connections", otherwise Excluded.
8a/3	Derivation of BR/EDR Link Keyfrom LE	[2] 2.4.2.4	C 2	C.2: Optional IF SM8a/1 Cross Transport Key Derivation Supported , otherwise
	LTK			Excluded.

"
"

Table 8b: Cross-Transport Key Derivation by Peripheral

Prerequisite: SM 1/2 "Peripheral Role ( Responder)"

Item	Capability	Reference	Support	Status	Comment
8b/1	Cross Transport Key Derivation Supported	[1] 2.3.5.7	C.1		C.1: Optional IF SM2/5 "LE Secure Connections", otherwise Excluded.
8b/3	Derivation of BR/EDR Link Keyfrom LE LTK	[2] 2.4.2.4	C 2		C.2: Optional IF SM8b/1 "Cross Transport Key Derivation Supported", otherwise Excluded.

Serial Port Profile

Table 0: Major Versions (X.Y)

Item Capability Reference Support Status Comment
0/2 SPPv1 .2 SPPv1 .2 C.1 C.1: Mandatoryto support one and onlyone major version.

Table 1 : Role Requirements

Item	Capability	Reference	Support Status	Comment
1/1	Device A(DevA)	[1] 2 2	C.1	C.1: Mandatoryto support at least one of SPP 1/1 "Device A(DevA)" OR SPP 1/2 "Device B (DevB)".
1/2	Device B (DevB)	[1] 2 2	C.1	C.1: Mandatoryto support at least one of SPP 1/1 "Device A(DevA)" OR SPP 1/2 "Device B (DevB)".

Table 2: Serial Port Service Support

Item	Capability	Reference	Support	Comment
2/1	Support of SPP as a standalone profile	[1] 1 2	O
2/1a	SPP as a standalone profile– Device A (DevA)	[1] 1 2	C.2, C.3	C.2: Mandatoryto support at least one of SPP 2/1a "SPP as a standalone profile– Device A(DevA)" OR SPP 2/1b "SPP as a standalone profile– Device B (DevB)" IF SPP 2/1 "Support of SPP as a standalone profile" is supported, otherwise Excluded. C.3: Optional IF SPP 1/1 "Device A(DevA)" is supported, otherwise Excluded.
2/1b	SPP as a standalone profile– Device B (DevB)	[1] 1 2	C.2, C.4	C.2: Mandatoryto support at least one of SPP 2/1a "SPP as a standalone profile– Device A(DevA)" OR SPP 2/1b "SPP as a standalone profile– Device B (DevB)" IF SPP 2/1 "Support of SPP as a standalone profile" is supported, otherwise Excluded. C.4: Optional IF SPP 1/2 "Device B (DevB)" is supported, otherwise Excluded

Table 3: Application Procedures

Item	Capability	Reference	Support	Comment
3/1	Establish link and set up virtual serial connection	[1] 3.1	C.1	C.1: Mandatory IF SPP 1/1 "Device A(DevA)" is supported, otherwise Optional.
3/2	Accept link and virtual serial connection establishment	[1] 3.1	C.2	C.2: Mandatory IF SPP 1/2 "Device B (DevB)" is supported, otherwise Optional.
3/3	Register Service record for application in local SDP database	[1] 3.1	C.3	C.3: Mandatory IF SPP 2/1b "SPP as a standalone profile– Device B (DevB)"is supported, otherwise Optional.

Table 4: SDP Dependencies

Prerequisite: SPP 2/1b "SPP as a standalone profile – Device B ( DevB)"

Item	Capability	Reference	Support	Status	Comment
4/1	ServiceClassIDList	[1] 6.1	M
4/2	ProtocolDescriptorList	[1] 6.1	M

4/6 BluetoothProfileDescriptorList [1] 6.1 M

Telephone Bearer Service

Table 0: Versions

Item	Capability	Reference	Support	Status			Comment
0/1	Telephone Bearer Service 1.0	[1] 2.3.1	M

Table 1: Transport Requirements

Item	Capability	Reference	Support	Status		Comment
1/2	Service Supported over LE	[1] 1.5	C.1			C.1: Mandatoryto support at least one of the defined transports .

Table 2: Telephone Bearer Service Requirements

Item	Capability	Reference	Support
2/1	Telephone Bearer Service	[1] 2.3.1	M
2/2	Bearer Provider Name Characteristic	[1] 3.1	M
2/4	Bearer UCI Characteristic	[1] 3.2	M
2/5	Bearer TechnologyCharacteristic	[1] 3.3	M
2/6	Bearer URI Schemes Supported List Characteristic	[1] 3.4	M
2/11	Bearer List Current Calls Characteristic	[1] 3.7	M
2/13	Content Control ID Characteristic	[1] 3.8	M
2/14	Status Flags Characteristic	[1] 3.9	M
2/17	Call State Characteristic	[1] 3.11	M
2/19	Call Control Point Characteristic	[1] 3.12	M
2/20	Call Control Point Optional Opcodes Characteristic	[1] 3.13	M
2/21	Termination Reason Characteristic	[1] 3.14	M
2/22	Incoming Call Characteristic	[1] 3 15	M

Table 3: Call Control Point Opcode Requirements

Prerequisite: TBS 2/19 “Call Control Point Characteristic”

Item	Capability	Reference	Support
3/1	Accept	[1] 3.12.1.1	M
3/2	Terminate	[1] 3.12.1.2	M
3/5	Originate	[1] 3.12.1.5	M

Table 4: GATT Requirements

Item	Capability	Reference	Support
4/1	Write Characteristic Value	[1] 1.4	M
4/2	Write Without Response	[1] 1.4	M
4/3	Notifications	[1] 1.4	M
4/4	Read Characteristic Descriptors	[1] 1.4	M
4/5	Write Characteristic Descriptors	[1] 1.4	M

Table 5: SDP Requirements

Prerequisite: TBS 1/1 “Service Supported over BR/EDR”
Item Capability Reference Support Status Comment

Telephony and Media Audio Profile

Table 1 : Role Requirements

Item Capability Reference Support Status Comment
1/1	Call Gateway (CG)	[4] 3.1	C.1	C.1: Mandatoryto support at least one ofTMAP 1/1 "Call Gateway(CG)" ORTMAP 1/2 "Call Terminal (CT)" ORTMAP 1/3 "Unicast Media Sender (UMS)" ORTMAP 1/4 "Unicast Media Receiver (UMR)" ORTMAP 1/5 "Broadcast Media Sender (BMS)" ORTMAP 1/6 "Broadcast Media Receiver (BMR)".
1/2	Call	[4] 3.1	C 1 v	C.1: Mandatoryto support at least one ofTMAP 1/1 "Call Gateway(CG)" ORTMAP 1/2 "Call Terminal (CT)" OR
	Terminal			TMAP 1/3 "Unicast Media Sender (UMS)" ORTMAP 1/4 "Unicast Media Receiver (UMR)" ORTMAP 1/5
	(CT)			"Broadcast Media Sender (BMS)" ORTMAP 1/6 "Broadcast Media Receiver (BMR)".
1/3	Unicast	[4] 3.1
	Media			TMAP 1/3 "Unicast Media Sender (UMS)" ORTMAP 1/4 "Unicast Media Receiver (UMR)" ORTMAP 1/5
	Sender (UMS)			"Broadcast Media Sender (BMS)" ORTMAP 1/6 "Broadcast Media Receiver (BMR)".
1/4	Unicast	[4] 3.1	C.1	C.1: Mandatoryto support at least one ofTMAP 1/1 "Call Gateway(CG)" ORTMAP 1/2 "Call Terminal (CT)" OR
	Media			TMAP 1/3 "Unicast Media Sender (UMS)" ORTMAP 1/4 "Unicast Media Receiver (UMR)" ORTMAP 1/5
	Receiver (UMR)			"Broadcast Media Sender (BMS)" ORTMAP 1/6 "Broadcast Media Receiver (BMR)".
1/6	Broadcast	[4] 3.1	C.1 C 2	C.1: Mandatoryto support at least one ofTMAP 1/1 "Call Gateway(CG)" ORTMAP 1/2 "Call Terminal (CT)" OR
	Media			TMAP 1/3 "Unicast Media Sender (UMS)" ORTMAP 1/4 "Unicast Media Receiver (UMR)" ORTMAP 1/5
	Receiver			"Broadcast Media Sender (BMS)" ORTMAP 1/6 "Broadcast Media Receiver (BMR)". C.2: Mandatory IF TMAP 1/4
	(BMR)			"Unicast Media Receiver (UMR)", otherwise Optional.
1/7	TMA Client	[4] 3.8	O
1/8	TMA	[4] 3.8
	Server			(GATT) Server", otherwise Mandatory.

.
C.1
C.1: Mandatoryto support at least one ofTMAP 1/1 "Call Gateway(CG)" ORTMAP 1/2 "Call Terminal (CT)" OR
,
C.3
v C.3: Excluded IF TMAP 1/5 "Broadcast Media Sender (BMS)" AND NOT GATT 1/2 "Generic Attribute Profile

Table 2: Transport Requirements

Item Capability Reference Support Status Comment
2/2 Profile supported over LE [4] 4.3 M

Table 3: Device Configuration Requirements

Item Capability	Reference	Support	Status			Comment
3/2 BR/EDR/LE	[4] 4.9	C.1				C.1: Mandatoryto support one and onlyone ofTMAP 3/1 "LE" ORTMAP 3/2 "BR/EDR/LE".

Table 10: Major Versions (X.Y)

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status		Comment
10/1	TMAP 1.0	[4]	M

Table 12: Call Gateway Profile and Service Dependencies

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support
12/1	Common Audio Profile	[4] 3.1	M
12/2	Basic Audio Profile	[4] 3.1	M
12/3	Call Control Profile	[4] 3.1	M

Table 13: Role Discovery Requirements

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status			Comment
13/1	Advertise Call GatewaySupport	[4] 3.4	O

Table 14: CG Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support
14/1	CAP Initiator	[4] 3.1	M
14/2	CAP Commander	[4] 3.1	M
14/3	CCP Call Control Server	[4] 3.1	M
14/4	VCP Volume Controller	[4] 3.1	M
14/5	Audio Source	[4] 3.1	M
14/6	Audio Sink	[4] 3.1	M

Table 15: Call Gateway Config Codec Operation Parameters

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support Status Comment
15/3	32_2 LC3: 32 kHz Sampling Frequency, 10 ms Frame Duration, 80 Octets (Audio Source)	[4] 3.5.1.4.1	M
15/6	32_2 LC3: 32 kHz Sampling Frequency, 10 ms Frame Duration, 80 Octets (Audio Sink)	[4] 3.5.1.4.1	M

Table 16: Call Gateway QoS Settings Requirements

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status Comment
16/3	32_2_1 LC3: 10000 SDU Interval , unframed, 80 Max SDU Size, 2 RTN, 10 Max_Transport_Latency(Audio Source)	[4] 3.5.1.4.2	M
16/6	32_2_1 LC3: 10000 SDU Interval , unframed, 80 Max SDU Size, 2 RTN, 10 Max_Transport_Latency(Audio Sink)	[4] 3.5.1.4.2	M

Table 17: Number of Concurrent Unicast Audio Streams, Channels, and Devices

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support
17/1	Configuration A: 1 bidirectional stream between CG and CT	[4] 3.5.1.5	M
17/2	Configuration B: 1 stream with 1 channel from CGto CT, 1 stream with 1 channel from 2nd CTto CG.	[4] 3.5.1.5	M
17/3	Configuration C: 1 stream with 1 channel from CGto CT, 1 bidirectional stream between CG and a 2nd CT	[4] 3.5.1.5	M
17/4	Configuration D: 1 stream with 1 channel from CGto CT, 1 bidirectional stream between CG and same CT	[4] 3.5.1.5	M

Table 18: Call Gateway PACS Characteristic Support Requirements

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status Comment
18/1	Sink Audio Locations characteristic	[4] 3.5.1.2	M
18/2	Source Audio Locations characteristic	[4] 3.5.1.2	M

Table 19: Call Gateway Audio Channel Allocation Audio Location Values

Prerequisite: TMAP 1/1 "Call Gateway (CG)"
Item Capability Reference Support Status Comment

Table 20: Call Gateway Audio Input Features

Prerequisite: TMAP 1/1 "Call Gateway (CG)"
Item Capability Reference Support Status Comment

Table 30: Major Versions (X.Y)

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item Capability Reference Support Status Comment

30/1 TMAP 1.0 [4] M

Table 32: UMS Profile and Service Dependencies

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support
32/1	Common Audio Profile	[4] 3.1	M
32/2	Basic Audio Profile	[4] 3.1	M
32/3	Media Control Profile	[4] 3.1	M

Table 33: Role Discovery Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status			Comment
33/1	Advertise Unicast Media Sender Support	[4] 3.4	O

Table 34: UMS Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support
34/1	CAP Initiator	[4] 3.1	M
34/2	CAP Commander	[4] 3.1	M
34/3	MCP Media Control Server	[4] 3.1	M
34/4	VCP Volume Controller	[4] 3.1	M
34/5	Audio Source	[4] 3.1	M

Table 35: Unicast Media Sender Config Codec Operation Parameters

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support Status	Comment
35/2	48_2 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 100 Octets	[4] 3.5.1.4.1	M
35/4	48_4 LC3: 48 kHz Sampling	[4]	C 1	C.1: Mandatoryto support at least one ofTMAP 35/4 "48_4 LC3: 48 kHz Sampling
	Frequency, 10 ms Frame	3.5.1.4.1		Frequency, 10 ms Frame Duration, 120 Octets" ORTMAP 35/6 "48_6 LC3: 48 kHz
	Duration, 120 Octets			Sampling Frequency, 10 ms Frame Duration, 155 Octets".
35/6	48_6 LC3: 48 kHz Sampling	[4]		C.1: Mandatoryto support at least one ofTMAP 35/4 "48_4 LC3: 48 kHz Sampling
	Frequency, 10 ms Frame	3.5.1.4.1		Frequency, 10 ms Frame Duration, 120 Octets" ORTMAP 35/6 "48_6 LC3: 48 kHz
	Duration, 155 Octets			Sampling Frequency, 10 ms Frame Duration, 155 Octets".

.
C.1

Table 36: Unicast Media Sender QoS Settings Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Comment
36/2	48_2_1 LC3: 10000 SDU Interval , unframed, 100 Max SDU Size, 5 RTN, 20 Max_Transport_Latency	[4] 3.5.1.4 2	M
36/4	48_4_1 LC3: 10000 SDU Interval , unframed, 120 Max	[4]	C.3	C.3: Mandatory IF TMAP 35/4 "48_4 LC3: 48 kHz Sampling
	SDU Size, 5 RTN, 20 Max_Transport_Latency	3.5.1.4 2		Frequency, 10 ms Frame Duration, 120 Octets", otherwise not defined.
36/6	48_6_1 LC3: 10000 SDU Interval , unframed, 155 Max	[4]	C.5	C.5: Mandatory IF TMAP 35/6 "48_6 LC3: 48 kHz Sampling
	SDU Size, 5 RTN, 20 Max_Transport_Latency	3.5.1.4 2		Frequency, 10 ms Frame Duration, 155 Octets", otherwise not defined.
36/10	48_2_2 LC3: 10000 SDU Interval , unframed, 100 Max SDU Size, 23 RTN, 60 Max_Transport_Latency	[4] 3.5.1.4 2	M
36/12	48_4_2 LC3: 10000 SDU Interval , unframed, 120 Max	[4]	C.3	C.3: Mandatory IF TMAP 35/4 "48_4 LC3: 48 kHz Sampling
	SDU Size, 23 RTN, 60 Max_Transport_Latency	3.5.1.4 2		Frequency, 10 ms Frame Duration, 120 Octets", otherwise not defined.
36/14	48_6_2 LC3: 10000 SDU Interval , unframed, 155 Max	[4]	C 5	C.5: Mandatory IF TMAP 35/6 "48_6 LC3: 48 kHz Sampling
	SDU Size, 23 RTN, 60 Max_Transport_Latency	3.5.1.4 2		Frequency, 10 ms Frame Duration, 155 Octets", otherwise not defined.

Table 37: Unicast Media Sender PACS Characteristic Support Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status			Comment
37/1	Sink Audio Locations characteristic	[4] 3.5.1 2	M

Table 38: Unicast Media Sender Audio Channel Allocation Audio Location Values

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status	Comment
38/1	Front Left Audio Location	[4] 3.5.1.4.1	M
38/2	Front Right Audio Location	[4] 3.5.1.4.1	M

Table 39: Unicast Media Sender BAP Audio Configuration

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"
Item Capability Reference Support Status Comment

Table 40: GMCS Generic Media Control Point Opcodes

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status	Comment
40/1	Play	[4] 3.6.1	M
40/2	Pause	[4] 3.6.1	M

Table 41: Call Gateway Audio Input Features

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"
Item Capability Reference Support Status Comment

Table 50: Major Versions (X.Y)

Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment

Table 52: BMS Profile and Service Dependencies

Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment

Table 53: Role Discovery Requirements

Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)" AND TMAP 1/8 "TMA Server"

Item	Capability	Reference	Support	Status	Comment
Table 54: BMS Inter-Layer Dependency Role Requirements Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item	Capability	Reference	Support	Status	Comment
Table 55: Broadcast Media Sender Codec Settings Requirements Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item	Capability	Reference	Support	Status	Comment
Table 56: Broadcast Media Sender QoS Settings Requirements Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item	Capability	Reference	Support	Status	Comment
Table 57: Broadcast Media Sender Audio Channel Allocation Audio Location Values Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item	Capability	Reference	Support	Status	Comment

Table 70: Major Versions (X.Y)

Prerequisite: TMAP 1/2 "Call Terminal (CT)"
Item Capability Reference Support Status Comment
70/1 TMAP 1.0 [4] M

Table 72: CT Profile and Service Dependencies

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

Item	Capability	Reference	Support	Status	Comment
72/1	Common Audio Profile	[4] 3.1	M
72/2	Basic Audio Profile	[4] 3.1	M

Table 73: Role Discovery Requirements

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

Item	Capability	Reference	Support	Status			Comment
73/1	Advertise Call Terminal Support	[4] 3.4	O

Table 74: CT Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

Item	Capability	Reference	Support	Comment
74/1	CAP Acceptor	[4] 3.1	M
74/2	CAP Commander	[4] 3.1	O
74/3	VCP Volume Renderer	[4] 3.1	C.1	C.1: Mandatory IF TMAP 74/4 "BAP Audio Sink", otherwise not defined.
74/4	BAP Audio Sink	[4] 3.1	C 2	C 2: Mandatoryto support at least one ofTMAP 74/4 "BAP Audio Sink" ORTMAP 74/5 "BAP Audio Source".
74/5	BAP Audio Source	[4] 3.1	C 2	C 2: Mandatoryto support at least one ofTMAP 74/4 "BAP Audio Sink" ORTMAP 74/5 "BAP Audio Source"

Table 75: Call Terminal PAC Records

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

Item	Capability	Reference	Support	Comment
75/1	16_1 LC3: 16 kHz Sampling Frequency, 7.5 ms Frame Duration, 30 Octets (Audio Sink)	[4] 3.5.1.1	C.1	C.1: Mandatory IF TMAP 74/4 "BAP Audio Sink", otherwise not defined.
75/2	32_1 LC3: 32 kHz Sampling Frequency, 7.5 ms Frame Duration, 60 Octets (Audio Sink)	[4] 3.5.1.1	C.1	C.1: Mandatory IF TMAP 74/4 "BAP Audio Sink", otherwise not defined.
75/3	32_2 LC3: 32 kHz Sampling Frequency, 10 ms Frame Duration, 80 Octets (Audio Sink)	[4] 3.5.1.1	C.1	C.1: Mandatory IF TMAP 74/4 "BAP Audio Sink", otherwise not defined.
75/4	16_1 LC3: 16 kHz Sampling Frequency, 7.5 ms Frame Duration, 30 Octets (Audio Source)	[4] 3.5.1.1	C 2	C 2: Mandatory IF TMAP 74/5 "BAP Audio Source", otherwise not defined.
75/5	32_1 LC3: 32 kHz Sampling Frequency, 7.5 ms Frame Duration, 60 Octets (Audio Source)	[4] 3.5.1.1	C 2	C 2: Mandatory IF TMAP 74/5 "BAP Audio Source", otherwise not defined.
75/6	32_2 LC3: 32 kHz Sampling Frequency, 10 ms Frame Duration, 80	[4] 3.5.1.1		C 2: Mandatory IF TMAP 74/5 "BAP Audio Source",
	Octets (Audio Source)			otherwise not defined.

C 2

Table 76: Call Terminal QoS Settings Requirements

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

Item	Capability	Reference	Support	Comment
76/1	16_1_1 LC3: 7500 SDU Interval , unframed, 30 Max SDU Size, 2 RTN, 8	[4]	C.1	C.1: Mandatory IF TMAP 74/4 "BAP Audio
	Max_Transport_Latency(Audio Sink)	3.5.1.4.2		Sink", otherwise not defined.
76/2	32_1_1 LC3: 7500 SDU Interval , unframed, 60 Max SDU Size, 2 RTN, 8	[4]	C.1	C.1: Mandatory IF TMAP 74/4 "BAP Audio
	Max_Transport_Latency(Audio Sink)	3.5.1.4.2		Sink", otherwise not defined.
76/3	32_2_1 LC3: 10000 SDU Interval , unframed, 80 Max SDU Size, 2 RTN, 10	[4]	C.1	C.1: Mandatory IF TMAP 74/4 "BAP Audio
	Max_Transport_Latency(Audio Sink)	3.5.1.4.2		Sink", otherwise not defined.
76/4	16_1_1 LC3: 7500 SDU Interval , unframed, 30 Max SDU Size, 2 RTN, 8	[4]	C.2	C.2: Mandatory IF TMAP 74/5 "BAP Audio
	Max_Transport_Latency(Audio Source)	3.5.1.4.2		Source", otherwise not defined.

76/5	32_1_1 LC3: 7500 SDU Interval , unframed, 60 Max SDU Size, 2 RTN, 8 Max_Transport_Latency(Audio Source)	[4] 3.5.1.4.2	C.2	C.2: Mandatory IF TMAP 74/5 "BAP Audio Source", otherwise not defined.
76/6	32_2_1 LC3: 10000 SDU Interval , unframed, 80 Max SDU Size, 2 RTN, 10	[4]	C.2	: an a or u o
	Max_Transport_Latency(Audio Source)	3.5.1.4.2		Source", otherwise not defined.

C.2
M
d
t
yIFTMAP74/5 "BAPA
di

Table 77: Number of Audio Outputs

Prerequisite: TMAP 1/2 "Call Terminal (CT)"
Item Capability Reference Support Status Comment
77/1 1 audio output [4] 3.5.1.5 M

Table 78: Number of Concurrent Unicast Audio Streams, Channels, and Devices

Prerequisite: TMAP 1/2 "Call Terminal (CT)"
Item Capability Reference Support Status Comment

Table 79: Call Terminal Multi-Stream Configurations

Prerequisite: TMAP 1/2 "Call Terminal (CT)"
Item Capability Reference Support Status Comment
79/1 Case 1: Multiple CT audio sink devices each with a single ASE
[4] 3.7 C.1 C.1: Mandatoryto support at least one ofTMAP 79/1 "Case 1: Multiple CT audio sink devices each with a single ASE" ORTMAP 79/2 "Case 2: Asingle CT audio sink device with multiple ASEs".

Table 90: Major Versions (X.Y)

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"
Item Capability Reference Support Status Comment
90/1 TMAP 1.0 [4] M

Table 92: UMR Profile and Service Dependencies

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support	Status	Comment
92/1	Common Audio Profile	[4] 3.1	M
92/2	Basic Audio Profile	[4] 3.1	M

Table 93: Role Discovery Requirements

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support	Status			Comment
93/1	Advertise Unicast Media Receiver Support	[4] 3.4	O

Table 94: UMR Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support
94/1	CAP Acceptor	[4] 3.1	M
94/2	CAP Commander	[4] 3.1	O
94/3	VCP Volume Renderer	[4] 3.1	M
94/4	BAP Audio Sink	[4] 3.1	M

Table 95: Unicast Media Receiver PAC Records

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support Status Comment
95/1	48_1 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 75 Octets	[4] 3.5.1.1	M
95/2	48_2 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 100 Octets	[4] 3.5.1.1	M
95/3	48_3 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 90 Octets	[4] 3.5.1.1	M

95/4	48_4 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 120 Octets	[4] 3.5.1.1	M
95/5	48_5 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 117 Octets	[4] 3.5.1.1	M
95/6	48_6 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 155 Octets	[4] 3.5.1.1	M

Table 96: Unicast Media Receiver QoS Settings Requirements

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support
96/1	48_1_1 LC3: 7500 SDU Interval , unframed, 75 Max SDU Size, 5 RTN, 15 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/2	48_2_1 LC3: 10000 SDU Interval , unframed, 100 Max SDU Size, 5 RTN, 20 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/3	48_3_1 LC3: 7500 SDU Interval , unframed, 90 Max SDU Size, 5 RTN, 15 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/4	48_4_1 LC3: 10000 SDU Interval , unframed, 120 Max SDU Size, 5 RTN, 20 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/5	48_5_1 LC3: 7500 SDU Interval , unframed, 117 Max SDU Size, 5 RTN, 15 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/6	48_6_1 LC3: 10000 SDU Interval , unframed, 155 Max SDU Size, 5 RTN, 20 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/9	48_1_2 LC3: 7500 SDU Interval , unframed, 75 Max SDU Size, 13 RTN, 75 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/10	48_2_2 LC3: 10000 SDU Interval , unframed, 100 Max SDU Size, 13 RTN, 95 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/11	48_3_2 LC3: 7500 SDU Interval , unframed, 90 Max SDU Size, 13 RTN, 75 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/12	48_4_2 LC3: 10000 SDU Interval , unframed, 120 Max SDU Size, 13 RTN, 100 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/13	48_5_2 LC3: 7500 SDU Interval , unframed, 117 Max SDU Size, 13 RTN, 75 Max_Transport_Latency	[4] 3.5.1.4.2	M
96/14	48_6_2 LC3: 10000 SDU Interval , unframed, 155 Max SDU Size, 13 RTN, 100 Max_Transport_Latency	[4] 3.5.1.4.2	M

Table 97: Unicast Media Receiver PACS Characteristic Support Requirements

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support	Status			Comment
97/1	Sink Audio Locations characteristic	[4]	M

Table 98: Unicast Media Receiver Sink Audio Locations Values

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support Status	Comment
98/1	Front Left Sink Audio	[4]		C.1: Mandatoryto support at least one ofTMAP 98/1 "Front Left Sink Audio Location" ORTMAP
	Location	3.5.1.2.1		98/2 "Front Right Sink Audio Location" OR TMAP 98/3 "Front Right and Front Left Sink Audio Locations".
98/2	Front Right Sink Audio	[4]	C 1	C.1: Mandatoryto support at least one ofTMAP 98/1 "Front Left Sink Audio Location" ORTMAP
	Location	3.5.1.2.1		98/2 "Front Right Sink Audio Location" OR TMAP 98/3 "Front Right and Front Left Sink Audio Locations".
98/3	Front Right and Front Left	[4]		C.1: Mandatoryto support at least one ofTMAP 98/1 "Front Left Sink Audio Location" ORTMAP
	Sink Audio Locations	3.5.1.2.1		98/2 "Front Right Sink Audio Location" OR TMAP 98/3 "Front Right and Front Left Sink Audio Locations".

C.1
.
C.1

Table 99: Number of Audio Outputs

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support	Status			Comment
99/1	1 audio output	[4] 3.7	M

Table 100: Unicast Media Receiver Multi-Stream Configurations

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support Status	Comment
100/1	Case 1: Multiple UMR audio sink	[4] 3.7		C.1: Mandatoryto support at least one ofTMAP 100/1 "Case 1: Multiple UMR audio sink
	devices each with a single ASE			devices each with a single ASE" ORTMAP 100/2 "Case 2: Asingle UMR audio sink device with multiple ASEs".

C.1

Table 110: Major Versions (X.Y)

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status	Comment
110/1	TMAP 1.0	[4]	M

Table 112: BMR Profile and Service Dependencies

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status	Comment
112/1	Common Audio Profile	[4] 3.1	M
112/2	Basic Audio Profile	[4] 3.1	M

Table 113: Role Discovery Requirements

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status			Comment
113/1	Advertise Broadcast Media Receiver Support	[4] 3.4	O

Table 114: BMR Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support
114/1	CAP Acceptor	[4] 3.1	M
114/3	VCP Volume Renderer	[4] 3.1	M
114/4	BAP Broadcast Sink	[4] 3.1	M

Table 115: Broadcast Media Receiver Codec Settings Requirements

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support
115/1	48_1 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 75 Octets	[4] 3.5.2.1	M
115/2	48_2 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 100 Octets	[4] 3.5.2.1	M
115/3	48_3 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 90 Octets	[4] 3.5.2.1	M
115/4	48_4 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 120 Octets	[4] 3.5.2.1	M
115/5	48_5 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 117 Octets	[4] 3.5.2.1	M
115/6	48_6 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 155 Octets	[4] 3.5.2.1	M

Table 116: Broadcast Media Receiver QoS Settings Requirements

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support
116/1	48_1_1 LC3: 7500 SDU Interval , unframed, 75 Max SDU Size, 4 RTN, 15 Max_Transport_Latency	[4] 3.5.2.3	M
116/2	48_2_1 LC3: 10000 SDU Interval , unframed, 100 Max SDU Size, 4 RTN, 20 Max_Transport_Latency	[4] 3.5.2.3	M
116/3	48_3_1 LC3: 7500 SDU Interval , unframed, 90 Max SDU Size, 4 RTN, 15 Max_Transport_Latency	[4] 3.5.2.3	M
116/4	48_4_1 LC3: 10000 SDU Interval , unframed, 120 Max SDU Size, 4 RTN, 20 Max_Transport_Latency	[4] 3.5.2.3	M
116/5	48_5_1 LC3: 7500 SDU Interval , unframed, 117 Max SDU Size, 4 RTN, 15 Max_Transport_Latency	[4] 3.5.2.3	M
116/6	48_6_1 LC3: 10000 SDU Interval , unframed, 155 Max SDU Size, 4 RTN, 20 Max_Transport_Latency	[4] 3.5.2.3	M
116/9	48_1_2 LC3: 7500 SDU Interval , unframed, 75 Max SDU Size, 4 RTN, 50 Max_Transport_Latency	[4] 3.5.2.3	M
116/10	48_2_2 LC3: 10000 SDU Interval , unframed, 100 Max SDU Size, 4 RTN, 65 Max_Transport_Latency	[4] 3.5.2.3	M
116/11	48_3_2 LC3: 7500 SDU Interval , unframed, 90 Max SDU Size, 4 RTN, 50 Max_Transport_Latency	[4] 3.5.2.3	M
116/12	48_4_2 LC3: 10000 SDU Interval , unframed, 120 Max SDU Size, 4 RTN, 65 Max_Transport_Latency	[4] 3.5.2.3	M
116/13	48_5_2 LC3: 7500 SDU Interval , unframed, 117 Max SDU Size, 4 RTN, 50 Max_Transport_Latency	[4] 3.5.2.3	M
116/14	48_6_2 LC3: 10000 SDU Interval , unframed, 155 Max SDU Size, 4 RTN, 65 Max_Transport_Latency	[4] 3.5.2.3	M

Table 117: BMR Codec Specific Audio Capability Support

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"
Item Capability Reference Support Status Comment
117/1 Multiple Audio Locations (More than 1 bit set in Sink Audio Locations) [4] 3.5.2. O
117/2 Two Audio Channels [4] 3.5.2 O

Table 118: BMR Audio Location Values

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Comment
118/1	Front Left Audio Location	[4] 3.5.2.2	C.1	C.1: Mandatoryto support at least one ofTMAP 118/1 "Front Left Audio Location" ORTMAP 118/2 "Front Right Audio Location" OR TMAP 118/3 "Front Right and Front Left Audio Locations".
118/2	Front Right Audio Location	[4] 3.5.2.2	C.1	C.1: Mandatoryto support at least one ofTMAP 118/1 "Front Left Audio Location" ORTMAP 118/2 "Front Right Audio Location" OR TMAP 118/3 "Front Right and Front Left Audio Locations".
118/3	Front Right and Front Left Audio Locations	[4] 3.5.2.2	C.1	C.1: Mandatoryto support at least one ofTMAP 118/1 "Front Left Audio Location" ORTMAP 118/2 "Front Right Audio Location" OR TMAP 118/3 "Front Right and Front Left Audio Locations".

Table 119: Number of Audio Outputs

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status			Comment
119/1	1 audio output	[4] 3.7	M

Table 120: LC3 Audio Configuration

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support Status	Comment
120/1	AC14: 1 BIS, Multiple Audio Channels/BIS, 1 Audio Stream	[4]	C.1	C.1: Mandatory IF TMAP 117/1 "Multiple Audio Locations (More than 1 bit set in Sink Audio Locations)" AND TMAP 117/2 "Two Audio Channels", otherwise not defined

Table 121: Multi-Stream Configurations

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Comment
121/1	Case 5: Multiple BMR devices ,	[4] 3.7	C.1: Mandatoryto support at least one ofTMAP 121/1 "Case 5: Multiple BMR devices ,
	each synchronized to a single		each synchronized to a single BIS" ORTMAP 121/2 "Case 6: Asingle BMR device
	BIS		synchronized to multiple BISes".

C.1

Table 130: CAP Procedure Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)" AND TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment

Table 131: Link Layer and HCI Features

Prerequisite: TMAP 1/1 "Call Gateway (CG)" OR TMAP 1/2 "Call Terminal (CT)" OR TMAP 1/3 "Unicast Media Sender (UMS)" OR TMAP 1/4 "Unicast Media Receiver (UMR)" OR TMAP 1/5 "Broadcast Media Sender (BMS)" OR TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status			Comment
131/1	LE2MPHY	[4] 3.2	M

Table 140: MCS Media Control Point Opcodes

Item	Capability	Reference	Support	Status	Comment
140/1	Play	[4] 3.6.1	C.1		C.1: Mandatory IF MCP 5/1 "Media Control Service", otherwise not defined.
140/2	Pause	[4] 3.6.1	C.1		C.1: Mandatory IF MCP 5/1 "Media Control Service", otherwise not defined.

Table 150: TMA Service Characteristic Support Requirements

Prerequisite: TMAP 1/7 "TMA Client"
Item Capability Reference Support Status Comment
150/1 TMAP Role Characteristic [4] 4.7.1 M

Table 151: GATT Requirements

Prerequisite: TMAP 1/7 "TMA Client"

Item	Capability	Reference	Support	Comment
151/1	GATT Client over LE	[4] 3.8	M
151/2	DiscoverAll PrimaryServices	[4] 3.8.1.3	C.1	C.1: Mandatoryto support at least one ofTMAP 151/2 "DiscoverAll PrimaryServices" ORTMAP 151/3 "Discover PrimaryServices byService UUID".
151/3	Discover PrimaryServices by Service UUID	[4] 3.8.1.3	C.1	C.1: Mandatoryto support at least one ofTMAP 151/2 "DiscoverAll PrimaryServices" ORTMAP 151/3 "Discover PrimaryServices byService UUID".
151/4	DiscoverAll characteristics of a Service	[4] 3.8.1.3	C.2	C 2: Mandatoryto support at least one ofTMAP 151/4 "DiscoverAll characteristics ofa Service" OR TMAP 151/5 "Discover Characteristics byUUID".
151/5	Discover Characteristics by	[4] 3.8.1.3		C 2: Mandatoryto support at least one ofTMAP 151/4 "DiscoverAll characteristics ofa
	UUID			Service" OR TMAP 151/5 "Discover Characteristics byUUID".
151/6	Read Characteristic Value	[4] 3.8.1.3	M

C.2

Table 152: Service Characteristic

Prerequisite: TMAP 1/8 "TMA Server"

Item	Capability	Reference	Support	Status			Comment
152/1	TMAP Role Characteristic	[4] 4.7.1	M

Table 153: TMAP Role Support

Prerequisite: TMAP 152/1 "TMAP Role Characteristic"

Item	Capability	Reference	Support	Comment
153/1	Call GatewaySupport	[4] 4.7.1 2	C.1	C.1: Mandatory IF TMAP 1/1 "Call Gateway(CG)", otherwise Excluded.
153/2	Call Terminal Support	[4] 4.7.1 2	C 2	C 2: Mandatory IF TMAP 1/2 "Call Terminal (CT)", otherwise Excluded.
153/3	Unicast Media Sender Support	[4] 4.7.1 2	C.3	C.3: Mandatory IF TMAP 1/3 "Unicast Media Sender (UMS)", otherwise Excluded.
153/4	Unicast Media Receiver Support	[4] 4.7.1 2	C.4	C.4: Mandatory IF TMAP 1/4 "Unicast Media Receiver (UMR)", otherwise Excluded.
153/6	Broadcast Media Receiver Support	[4] 4.7.1 2	C.6	C.6: Mandatory IF TMAP 1/6 "Broadcast Media Receiver (BMR)", otherwise Excluded.

Table 154: GATT Requirements

Prerequisite: TMAP 1/8 "TMA Server"
Item Capability Reference Support Status Comment
154/1 GATT Server over LE [4] 4.8 M

Table 155: SDP Requirements

Prerequisite: TMAP 1/8 "TMA Server" AND TMAP 2/1 "Profile supported over BR/EDR"
Item Capability Reference Support Status Comment

Table 156: GAP Requirements

Prerequisite: TMAP 1/7 "TMA Client" OR TMAP 1/8 "TMA Server"
Item Capability Reference Support Status Comment
156/1 LE security mode 1 [4] 4.8 M

Volume Control Profile

Table 1 : Role Requirements

Item	Capability	Reference	Support	Status	Comment
1/1	Volume Renderer	[1] 3.0	C.1		C.1: Mandatoryto support at least one.
1/2	Volume Controller	[1] 4.0	C.1		C.1: Mandatoryto support at least one.

Table 2: Transport Requirements

Item	Capability	Reference	Support	Status			Comment
2/2	Profile supported over LE	[1] 2.4	C.1				C.1: Mandatoryto support at least one.

Table 3: Volume Renderer, X.Y Versions

Prerequisite: VCP 1/1 "Volume Renderer"
Item Capability Reference Support Status Comment
3/1 Volume Control Profile 1.0 [1] M

Table 5: Service Requirements

Prerequisite: VCP 1/1 "Volume Renderer"

Item	Capability	Reference	Support	Status	Comment
5/1	Volume Control Service	[1] 3.0	M
5/4	Extended Advertising	[1] 6.1.1.1	M

Table 6: GAP Requirements – Volume Renderer Role

Prerequisite: VCP 1/1 "Volume Renderer"

Item	Capability	Reference	Support	Comment
6/1	LE security mode 1	[1] 5.1	C.1	C.1: Mandatory IFVCP 2/2 "Profile supported over LE", otherwise not defined.
6/2	Unauthenticated Pairing (LE security mode 1 level 2) with LE Secure Connections Pairing only	[1] 5.1	C.1	C.1: Mandatory IFVCP 2/2 "Profile supported over LE", otherwise not defined.
6/3	Authenticated Pairing (LE security mode 1 level 3) with LE Secure Connections Pairing only	[1] 5.1	C.3	C.3: Optional IFVCP 2/2 "Profile supported over LE", otherwise not defined.
6/8	Minimum 128 Bit entropy key(LE)	[1] 5.1	C.1	C.1: Mandatory IFVCP 2/2 "Profile supported over LE", otherwise not defined.

Table 7: SM Requirements – Volume Renderer Role

Prerequisite: VCP 1/1 "Volume Renderer"
Item Capability Reference Support Status Comment
7/1 LE Secure Connections [1] 5.1 C.1 C.1: Mandatoryto support at least one.

Table 8: Volume Controller, X.Y Versions

Prerequisite: VCP 1/2 "Volume Controller"
Item Capability Reference Support Status Comment
8/1 Volume Control Profile 1.0 [1] M

Table 10: Volume Control Service Support

Prerequisite: VCP 1/2 "Volume Controller"
Item Capability Reference Support Status Comment
10/1 Volume Control Service [1] 4.0 M

Table 11: Volume Control Service Characteristic Support Requirements

Prerequisite: VCP 10/1 "Volume Control Service"

Item	Capability	Reference	Support	Status	Comment
11/1	Volume State	[1] 4.3.1	M
11/2	Volume Control Point	[1] 4.3.1	M

Table 12: Volume Control Service Procedure Support Requirements

Prerequisite: VCP 10/1 "Volume Control Service"

12/1	Configure Volume State Notifications	[1] 4.4.1, 4.4.1.1	M
12/2	Read Volume State	[1] 4.4.1, 4.4.1.2	M
12/6	Set Absolute	[1] 4.4.1,	C.2	C 2: Mandatory IF NOT VCP 12/7 Relative Volume Down AND NOT VCP 12/8 Relative Volume Up
	Volume	4.4.1.6.5		AND NOT VCP 12/9 "Unmute/ Relative Volume Down" AND NOT VCP 12/10 "Unmute/ Relative Volume Up", otherwise Optional.
12/11	Mute	[1] 4.4.1, 4.4.1.6.6	O
12/12	Unmute	[1] 4.4.1, 4 4 1 6 7	O

"
"
"
"

Table 13: Volume Offset Control Service Characteristic Support Requirements

Prerequisite: VCP 10/2 "Volume Offset Control Service"
Item Capability Reference Support Status Comment

Table 14: Volume Offset Control Service Procedure Support Requirements

Prerequisite: VCP 10/2 "Volume Offset Control Service"
Item Capability Reference Support Status Comment

Table 15: Audio Input Control Service Characteristic Support Requirements

Prerequisite: VCP 10/3 "Audio Input Control Service"
Item Capability Reference Support Status Comment

Table 16: Audio Input Control Service Procedure Support Requirements

Prerequisite: VCP 10/3 "Audio Input Control Service"
Item Capability Reference Support Status Comment

Table 17: Volume Controller GATT Requirements

Prerequisite: VCP 1/2 "Volume Controller"