258467-Q332415-20260617-LEA（4/4）

📎 原始文档：https://www.kdocs.cn/l/cv8flEREHVhl

上一部分 · 返回目录

Item	Capability	Reference	Support	Status	Comment
16/1	Bondable mode (LE)	[ 1] 5.1	C.1		C. 1: Mandatory IF MICP 2/2 "Profile supported over LE", otherwise not defined.
16/3	LE security mode 1	[ 1] 5	C.1		C. 1: Mandatory IF MICP 2/2 "Profile supported over LE", otherwise not defined.
16/4	Unauthenticated Pairing (LE security mode 1 level 2) with LE Secure Connections Pairing only	[ 1] 5	O
16/5	Authenticated Pairing (LE security mode 1 level 3) with LE Secure Connections Pairing only	[ 1] 5	O
16/6	LE security mode 1 level 4	[ 1] 5	O

16/7 Minimum 128 Bit entropy key (LE)
[ 1] 5.1 C.3 C.3: Mandatory IF MICP 16/4 "Unauthenticated Pairing (LE security mode 1 level 2) with LE Secure Connections Pairing only" OR MICP 16/5 "Authenticated Pairing (LE security mode 1 level 3) with LE Secure Connections Pairing only", otherwise not defined.

Microphone Control Service

Table 0: X.Y Versions

Item	Capability	Reference	Support	Status	Comment
0/1	MICS v1 .0	[ 1] 2.1	M

Table 1: Transport Requirements

Item	Capability	Reference	Support	Status	Comment
1/2	Service supported over LE	[ 1] 1.5	C.1		C. 1: Mandatory to support at least one.

Table 2: Microphone Control Service Requirements

Item	Capability	Reference	Support	Status	Comment
2/1	Mute Characteristic	[ 1] 3.1.1	M

Table 3: GATT Requirements

Item	Capability	Reference		Support	Status	Comment
3/1	Write Characteristic Value	[ 1]	1.4	M
3/2	Notifications	[ 1]	1.4	M
3/3	Read Characteristic Descriptors	[ 1]	1.4	M
3/4	Write Characteristic Descriptors	[ 1]	1.4	M

Table 4: SDP Requirements

Prerequisite: MICS 1/1 "Service supported over BR/EDR"
Item Capability Reference Support Status Comment

Published Audio Capabilities Service

Table 0: X.Y Versions
Item Capability Reference Support Status Comment

Table 1: X.Y.Z Versions

Item	Capability	Reference	Support	Status	Comment
1/2	PACS v1 .0.2	[5]	C.1		C. 1: Optional to support one and only one.

Table 2: Transport Requirements

2/2 Service supported over LE [ 1] 1.5 C.1 C. 1: Mandatory to support at least one.

Table 3: Published Audio Capabilities Service

Item	Capability	Reference	Support	Status	Comment
3/1	Sink PAC Characteristic	[ 1] 3.1.1	C.1		C. 1: Mandatory to support at least one.
3/2	Sink Audio Locations Characteristic	[ 1] 3.2.1	C.2		C.2: Optional IF PACS 3/1 "Sink PAC Characteristic", otherwise Excluded.
3/3	Source PAC Characteristic	[ 1] 3.3.1	C.1		C. 1: Mandatory to support at least one.
3/4	Source Audio Locations Characteristic	[ 1] 3.4.1	C.3		C.3: Optional IF PACS 3/3 "Source PAC Characteristic", otherwise Excluded.
3/5	Available Audio Contexts Characteristic	[ 1] 3.5.1	M

3/6 Supported Audio Contexts [ 1] 3.6.1 M
Characteristic

Table 4: Service Requirements

Item	Capability	Reference	Support	Status	Comment
4/13	Changeable Available Audio Contexts Characteristic	[ 1] 3.5.1	M
4/14	Notifiable Available Audio Contexts Characteristic	[ 1] 3.5.1	M
4/15	Changeable Supported Audio Contexts Characteristic	[ 1] 3.6.1	C.11		C. 11: Optional IF PACS 3/6 "Supported Audio Contexts Characteristic", otherwise Excluded.

4/16 Notifiable Supported Audio [ 1] 3.6.1 C.12 C. 12: Mandatory IF PACS 4/15 "Changeable Supported Audio
Contexts Characteristic Contexts Characteristic", otherwise Excluded.

Table 5: GAP Requirements

Item	Capability	Reference	Support	Status	Comment
5/1	Bondable mode (LE)	[ 1] 3	C.1		C. 1: Optional IF PACS 2/2 "Service supported over LE", otherwise not defined.

Table 6: GATT Requirements
Table 7: SDP Requirements
Prerequisite: PACS 2/1 "Service supported over BR/EDR"

Public Broadcast Profile

Table 1: Role Requirements
Table 2: Transport Requirements
Table 3: X.Y Versions

Item	Capability	Reference		Support	Status	Comment
6/1	Read Characteristic Descriptors	[ 1]	1.4	M
6/2	Write Characteristic Descriptors	[ 1]	1.4	M
6/3	Notifications	[ 1]	1.4	M
6/4	Write Characteristic Value	[ 1]	1.4	M
6/7	GATT Server over LE	[ 1]	1.4	C.2		C.2: Mandatory IF PACS 2/2 "Service supported over LE", otherwise not defined.

Item
Capability
Reference
Support
Status
Comment

3/1 PBP v1 .0 [ 1] M

Table 4: X.Y.Z Versions

Prerequisite: PBP 1/1 "Public Broadcast Source"

4/1 PBP v1 .0.1 [4] O
Table 5: Public Broadcast Source Role-Support Requirements
Prerequisite: PBP 1/1 "Public Broadcast Source"

Item	Capability	Reference	Support	Status	Comment
5/1	Initiator	[ 1] 3.1. 1,[4] 3.1	M

5/2 BAP Broadcast Source [ 1] 2. 1,[4] 3.1 M

Table 6: Public Broadcast Source Role-Features

Prerequisite: PBP 1/1 "Public Broadcast Source"

Item	Capability	Reference	Support	Status	Comment
6/3	Public Broadcast Announcement	[ 1] 4	M
6/4	Standard Quality Public Broadcast Audio	[ 1] 4.1	M
6/6	Encrypted Broadcast Isochronous Stream	[ 1] 4	C.2		C.2: Mandatory to support at least one.
6/7	Unencrypted Broadcast Isochronous Stream	[ 1] 4	C.2		C.2: Mandatory to support at least one.

6/8 Broadcast Name AD Type [ 1] 5 M

Table 7: Standard Quality Public Broadcast Audio Configuration Support Requirements

Prerequisite: PBP 6/4 "Standard Quality Public Broadcast Audio"

Item	Capability	Reference	Support	Status	Comment
7/1	16_2_ 1 LC3: 10000 SDU Interval, unframed, 40 Max SDU Size, 2 RTN, 10 Max_Transport_Latency	[ 1] 4.2	M

7/3 16_2_2 LC3: 10000 SDU Interval, unframed, 40 Max SDU Size, 4 RTN, 60 Max_Transport_Latency
[ 1] 4.2 M
Table 8: High Quality Public Broadcast Audio Configuration Support Requirements
Prerequisite: PBP 6/5 "High Quality Public Broadcast Audio"
Item Capability Reference Support Status Comment
Table 9: X.Y Versions
Prerequisite: PBP 1/2 "Public Broadcast Sink"

9/1 PBP v1 .0 [ 1] M
Table 10: X.Y.Z Versions
Prerequisite: PBP 1/2 "Public Broadcast Sink"

10/1 PBP v1 .0.1 [4] O

Table 11: Public Broadcast Sink Role-Support Requirements

Prerequisite: PBP 1/2 "Public Broadcast Sink"

Item	Capability	Reference	Support	Status	Comment
11/1	Acceptor	[ 1] 3.2. 1,[4] 3.1	M
11/2	BAP Broadcast Sink	[ 1] 3.2. 1,[4] 3.1	M

Table 12: Public Broadcast Sink Role-Features

Prerequisite: PBP 1/2 "Public Broadcast Sink"

12/1 Standard Quality Public Broadcast Audio [ 1] 4.1 M
Table 13: Standard Quality Public Broadcast Audio configuration support requirements
Prerequisite: PBP 12/1 "Standard Quality Public Broadcast Audio"
Table 14: High Quality Public Broadcast Audio Configuration Support Requirements
Prerequisite: PBP 12/2 "High Quality Public Broadcast Audio"
Table 15: X.Y Versions
Prerequisite: PBP 1/3 "Public Broadcast Assistant"
Table 16: X.Y.Z Versions
Prerequisite: PBP 1/3 "Public Broadcast Assistant"
Table 17: Public Broadcast Assistant Role-Support Requirements
Prerequisite: PBP 1/3 "Public Broadcast Assistant"

Item	Capability	Reference Support Status Comment
13/1	16_2_ 1 LC3: 10000 SDU Interval, unframed, 40 Max SDU Size, 2 RTN, 10 Max_Transport_Latency	[ 1] 4.2	M
13/2	24_2_ 1 LC3: 10000 SDU Interval, unframed, 60 Max SDU Size, 2 RTN, 10 Max_Transport_Latency	[ 1] 4.2	M
13/3	16_2_2 LC3: 10000 SDU Interval, unframed, 40 Max SDU Size, 4 RTN, 60 Max_Transport_Latency	[ 1] 4.2	M
13/4	24_2_2 LC3: 10000 SDU Interval, unframed, 60 Max SDU Size, 4 RTN, 60 Max_Transport_Latency	[ 1] 4.2	M
Item	Capability Reference Support	Status		Comment
Item	Capability Reference Support	Status		Comment
15/1	PBP v1 .0 [ 1] M
Item	Capability Reference Support	Status		Comment
16/1	PBP v1 .0.1 [4] O
Item	Capability Reference	Support	Status	Comment
17/1 Commander [ 1] 3.3. 1,[4] 3.1 M

17/2 BAP Broadcast Assistant [ 1] 3.3. 1,[4] 3.1 M

BR/EDR Radio Physical Layer

Table 1: RF Capabilities

Item	Capability	Reference	Support	Status	Comment
1/1	Power Class 1	[ 1] 3	C.5		C.5: Mandatory to support at least one.
1/4	Power Control	[ 1] 3	C.1		C. 1: Mandatory IF RF 1/1 "Power Class 1", otherwise Optional IF RF 1/2 "Power Class 2" OR RF 1/3 "Power Class 3", otherwise Excluded.
1/5	1-slot packets supported	[2] 6.5	M
1/6	3-slot packets supported	[2] 6.5	O
1/7	5-slot packets supported	[2] 6.5	O
1/8	79 Channels	[ 1] 2	M
1/9	Support for GFSK modulation	[ 1] 3.1	M
1/10	Support for π/4-DQPSK modulation	[ 1] 3.2	O
1/11	Support for 8DPSK modulation	[ 1] 3.2	C.3		C.3: Optional IF RF 1/10 "Support for π/4-DQPSK modulation", otherwise Excluded.

1/12 Enhanced Power [ 1] 3 Control RFCOMM Table 0: Major Versions (X.Y)		C.4		C.4: Optional IF RF 1/4 "Power Control", otherwise Excluded.
Item Capability	Reference	Support	Status	Comment
0/2 RFCOMM v1 .2 with TS 07.10	[ 1]	C.1	C. 1: Mandatory to support one and only one of RFCOMM 0/1 "RFCOMM v1 .1 with TS 07. 10" OR RFCOMM 0/2 "RFCOMM v1 .2 with TS 07. 10".

Table 1: Supported Procedures

Item	Capability	Reference	Support	Status	Comment
1/1	Initialize RFCOMM Session	[ 1] 5.2.1	C.5		C.5: Mandatory to support at least one of RFCOMM 1/1 "Initialize RFCOMM Session" OR RFCOMM 1/2 "Respond to Initialization of an RFCOMM Session".
1/2	Respond to Initialization of an RFCOMM Session	[ 1] 5.2.1	C.5		C.5: Mandatory to support at least one of RFCOMM 1/1 "Initialize RFCOMM Session" OR RFCOMM 1/2 "Respond to Initialization of an RFCOMM Session".
1/3	Shutdown RFCOMM Session	[ 1] 5.2.2	M
1/4	Respond to a Shutdown of an RFCOMM Session	[ 1] 5.2.2	M
1/5	Establish DLC	[ 1] 5.2.1	C.2		C.2: Mandatory IF RFCOMM 1/1 "Initialize RFCOMM Session", otherwise Excluded.
1/6	Respond to Establishment of a DLC	[ 1] 5.2.1	C.1		C. 1: Mandatory IF RFCOMM 1/2 "Respond to Initialization of an RFCOMM Session", otherwise Excluded.
1/7	Disconnect DLC	[ 1] 5.2	M
1/8	Respond to Disconnection of a DLC	[ 1] 5.2	M
1/9	Respond to and send MSC Command	[ 1] 2.2	M
1/10	Initiate Transfer Information	[ 1] 5.1	M
1/11	Respond to Test Command	[ 1] 4.3	M
1/12	Send Test Command	[ 1] 4.3	O
1/13	React to Aggregate Flow Control	[ 1] 6.3	M
1/14	Respond to RLS Command	[ 1] 5.5.2	M
1/15	Send RLS Command	[ 1] 5.5.2	O
1/16	Respond to PN Command	[ 1] 5.5.3	M
1/17	Send PN Command	[ 1] 5.5.3	C.3		C.3: Mandatory IF RFCOMM 1/1 "Initialize RFCOMM Session", otherwise Optional.
1/18	Send Non-Supported Command (NSC) response	[ 1] 4.3	C.4		C.4: Mandatory IF RFCOMM 0/2 "RFCOMM v1 .2 with TS 07. 10", otherwise Optional.

1/19	Respond to RPN Command	[ 1] 5.5.1	M
1/20	Send RPN Command	[ 1] 5.5.1	O
1/21	Closing Multiplexer by First Sending a DISC Command	[ 1] 5.2.2	O

1/22 Support of Credit Based Flow [ 1] 6.5 M
Control

LE Radio Physical Layer

Table 1: Bluetooth LE RF Capabilities

Item	Capability	Reference	Support	Status	Comment
1/1	LE Transmitter	[ 1] 3	C.1		C. 1: Mandatory to support at least one. Note: Selecting both RFPHY 1/1 "LE Transmitter" and RFPHY 1/2 "LE Receiver" is equivalent to selecting RFPHY 1/3 "LE Transceiver" and vice versa.
1/2	LE Receiver	[ 1] 4	C.1		C. 1: Mandatory to support at least one. Note: Selecting both RFPHY 1/1 "LE Transmitter" and RFPHY 1/2 "LE Receiver" is equivalent to selecting RFPHY 1/3 "LE Transceiver" and vice versa.
1/3	LE Transceiver	[ 1] 3, 4	C.1		C. 1: Mandatory to support at least one. Note: Selecting both RFPHY 1/1 "LE Transmitter" and RFPHY 1/2 "LE Receiver" is equivalent to selecting RFPHY 1/3 "LE Transceiver" and vice versa.
1/4	LE 2M PHY	[2] 3, 4	C.2		C.2: Optional IF CORE 1a/50 "Controller Core v5 .0 or later", otherwise Excluded.
1/5	Stable Modulation IndexTransmitter	[2] 3.1.1	C.3		C.3: Optional IF CORE 1a/50 "Controller Core v5 .0 or later" AND (RFPHY 1/1 "LE Transmitter" OR RFPHY 1/3 "LE Transceiver"), otherwise Excluded.
1/6	Stable Modulation IndexReceiver	[2] 3.1.1	C.4		C.4: Optional IF CORE 1a/50 "Controller Core v5 .0 or later" AND (RFPHY 1/2 "LE Receiver" OR RFPHY 1/3 "LE Transceiver"), otherwise Excluded.
1/7	LE Coded PHY	[2] 3, 4	C.2		C.2: Optional IF CORE 1a/50 "Controller Core v5 .0 or later", otherwise Excluded.
1/8	Transmitting Constant Tone Extensions	[3] 5	C.10		C. 10: Optional IF CORE 1a/51 "Controller Core v5 .1 or later" AND (RFPHY 1/1 "LE Transmitter" OR RFPHY 1/3 "LE Transceiver"), otherwise Excluded.
1/9	2 µs Antenna Switching During Constant Tone Extension Transmission (AoD)	[3] 5	C.5		C.5: Optional IF RFPHY 1/8 "Transmitting Constant Tone Extensions", otherwise Excluded.
1/10	1 µs Antenna Switching During Constant Tone Extension Transmission (AoD)	[3] 5	C.6		C.6: Optional IF RFPHY 1/9 "2 µs Antenna Switching During Constant Tone Extension Transmission (AoD)", otherwise Excluded.
1/11	2 µs Antenna Sampling During Constant Tone Extension Reception (AoD)	[3] 5	C.11		C. 11: Optional IF CORE 1a/51 "Controller Core v5 .1 or later" AND (RFPHY 1/2 "LE Receiver" OR RFPHY 1/3 "LE Transceiver"), otherwise Excluded.
1/12	2 µs Antenna Switching and Sampling During Constant Tone Extension Reception (AoA)	[3] 5	C.7		C.7: Optional IF RFPHY 1/11 "2 µs Antenna Sampling During Constant Tone Extension Reception (AoD)", otherwise Excluded.
1/13	1 µs Antenna Sampling During Constant Tone Extension Reception (AoD)	[3] 5	C.7		C.7: Optional IF RFPHY 1/11 "2 µs Antenna Sampling During Constant Tone Extension Reception (AoD)", otherwise Excluded.

1/14 1 µs Antenna Switching and [3] 5 C.8
Sampling During Constant Tone
Extension Reception (AoA)
C.8: Mandatory IF RFPHY 1/12 "2 µs Antenna Switching and Sampling During Constant Tone Extension Reception (AoA)" AND RFPHY 1/13 "1 µs Antenna Sampling During Constant Tone Extension Reception (AoD)", otherwise Excluded.

Table 3: Channel Sounding Capabilities

Prerequisite: ((RFPHY 1/1 "LE Transmitter"AND RFPHY 1/2 "LE Receiver") OR RFPHY 1/3 "LE Transceiver") AND RFPHY 1/16 "Channel Sounding"
Item Capability Reference Support Status Comment

Service Discovery Protocol

Table 1b: Role Requirements

Item	Capability	Reference	Support	Status	Comment
1b/1	Server	[ 1] 2.1	C.1		C. 1: Mandatory to support at least one.
1b/2	Client	[ 1] 2.1	C.1		C. 1: Mandatory to support at least one.

Table 2: Service Search Response

Prerequisite: SDP 1b/1 "Server"

2/1 Service Search Response [ 1] 4.5.2 M

Table 4: Service Attribute Response

Prerequisite: SDP 1b/1 "Server"

Item	Capability	Reference	Support	Status	Comment
4/1	Service Attribute Response	[ 1] 4.6.2	M
4/2	Generates continuation state in Service Attribute Response	[ 1] 4.3, 4.6.2	O
4/3	Service Attribute Response with AdditionalProtocolDescriptorList attribute	[ 1] 4.5.2, 5.1.6	O

Table 6: Service Search Attribute Response

Prerequisite: SDP 1b/1 "Server"

Item	Capability	Reference	Support	Status	Comment
6/1	Service Search Attribute Response	[ 1] 4.7.2	M
6/2	Generates continuation state in Service Search Attribute Response	[ 1] 4.3, 4.7.2	O
6/3	Service Search Attribute Response with AdditionalProtocolDescriptorList attribute	[ 1] 4.7.2, 5.1.6	O

Table 7: Invalid Service Search Attribute Request

Prerequisite: SDP 1b/1 "Server"

7/1 Error response to Service Search Attribute Request [ 1] 4.4 M
Table 8: Service Browsing
Prerequisite: SDP 1b/1 "Server"
Item Capability Reference Support Status Comment
Table 9: Attributes Present in IUT

Item	Capability	Reference	Support	Status	Comment
9/2	ProtocolDescriptorList	[ 1] 5.1.5	O
9/9	ServiceName	[ 1] 5.1.15	O
9/14	BluetoothProfileDescriptorList	[ 1] 5.1.11	O
9/18	ServiceRecordHandle	[ 1] 5.1.1	M
9/19	ServiceClassIDList	[ 1] 5.1.2	M

Table 10: Service Attribute Request

Prerequisite: SDP 1b/2 "Client"
Item Capability Reference Support Status Comment
Table 11: Service Search Attribute Request
Prerequisite: SDP 1b/2 "Client"
Item Capability Reference Support Status Comment

BR/EDR Security

Table 1: Security Mechanisms

Item	Capability	Reference	Support	Status	Comment
1/1	Legacy Security	[ 1] 1	M

1/2 Secure Simple Pairing [ 1] 1 M

Table 2: Security Algorithms

Item	Capability	Reference		Support	Status	Comment
2/1	E0 encryption	[ 1]	1	C.1		C. 1: Mandatory IF SEC 1/1 "Legacy Security" OR SEC 1/2 "Secure Simple Pairing", otherwise Excluded.
2/3	Legacy authentication	[ 1]	1	C.1		C. 1: Mandatory IF SEC 1/1 "Legacy Security" OR SEC 1/2 "Secure Simple Pairing", otherwise Excluded.
2/3a	Secure Simple Pairing Authentication	[ 1]	1	C.5		C.5: Mandatory IF SEC 1/2 "Secure Simple Pairing" OR SEC 1/3 "Secure Connections", otherwise Excluded.
2/5	E3 key generation	[ 1]	1	C.3		C.3: Mandatory IF SEC 1/1 "Legacy Security", otherwise Excluded.
2/6	AES key generation h3	[ 1]	1	C.5		C.5: Mandatory IF SEC 1/2 "Secure Simple Pairing" OR SEC 1/3 "Secure Connections", otherwise Excluded.

2/7 P-192 elliptic curve [ 1] 1 C.4 C.4: Mandatory IF SEC 1/2 "Secure Simple Pairing", otherwise Excluded.

Table 3: Broadcast Encryption Options

Item	Capability	Reference	Support	Status	Comment
3/1	No encryption	[ 1] 4.2	M
3/2	Point-to-point only encryption	[ 1] 4.2	M

Table 4: LMP Requirements

Item	Capability	Reference	Support	Status	Comment
4/1	Encryption	[ 1] 1	M

4/2 Secure Simple Pairing (Controller [ 1] 1 C.1 C. 1: Mandatory IF SEC 1/2 "Secure Simple Pairing", otherwise
Support) not defined.

Security Manager

Table 1: Role Requirements

Item	Capability	Reference	Support	Status	Comment
1/1	Central Role (Initiator)	[ 1] 2.4	C.1		C. 1: Mandatory to support at least one.

1/2 Peripheral Role (Responder) [ 1] 2.4 C.1 C. 1: Mandatory to support at least one.

Table 2: Security Properties

Item	Capability	Reference	Support	Status	Comment
2/1	Authenticated MITM protection	[ 1] 2.3.1	O
2/2	Unauthenticated no MITM protection	[ 1] 2.3.1	C.1		C. 1: Mandatory IF SM 2/1 "Authenticated MITM protection", otherwise Optional.
2/3	No security requirements	[ 1] 2.3.1	M

2/5 LE Secure Connections [ 1] 2.3.1 O

Table 3: Encryption Key Size

Prerequisite: SM 2/1 "Authenticated MITM protection" OR SM 2/2 "Unauthenticated no MITM protection" OR SM 4/3 "Out of Band"
Item Capability Reference Support Status Comment
3/1 Encryption Key Size [ 1] 2.3.4 M
Table 4: Pairing Method

Item	Capability	Reference	Support	Status	Comment
4/1	Just Works	[ 1] 2.3.5	O

4/2 Passkey [ 1] 2.3.5 C.1 C. 1: Mandatory to support at least one IF SM 2/1 "Authenticated MITM protection", Entry otherwise Excluded.

Table 5: Security Initiation

Item	Capability	Reference	Support	Status	Comment
5/1	Encryption Setup using STK	[ 1] 2.4	C.3		C.3: Mandatory IF SM 2/1 "Authenticated MITM protection" OR SM 2/2 "Unauthenticated no MITM protection" OR SM 4/3 "Out of Band", otherwise Excluded.
5/2	Encryption Setup using LTK	[ 1] 2.4	O

5/3	Peripheral Initiated Security	[ 1] 2.4.6	C.1		C. 1: Optional IF SM 1/2 "Peripheral Role (Responder)", otherwise Excluded.
5/4	Peripheral Initiated Security-Central response	[ 1] 2.4.6	C.2		C.2: Mandatory IF SM 1/1 "Central Role (Initiator)", otherwise Excluded.
5/5	CT2 bit	[2] 2.4.2.4 , 3.5.2	C.4		C.4: Excluded IF NOT SM 8a/1 "Cross Transport Key Derivation Supported"AND NOT SM 8b/1 "Cross Transport Key Derivation Supported", otherwise Mandatory IF CORE 2a/50 "Host Core v5 .0 or later", otherwise Optional.

Table 6: Signing Algorithm

Item	Capability	Reference	Support	Status	Comment
6/1	Signing Algorithm-Generation	[ 1] 2.4	O

6/2 Signing Algorithm-Resolving [ 1] 2.4 O

Table 7a: Key Distribution by Central

Prerequisite: SM 1/1 "Central Role (Initiator)"

Item	Capability	Reference	Support	Status	Comment
7a/1	Encryption Key	[ 1] 2.4.3	O
7a/2	Identity Key	[ 1] 2.4.3	O

7a/3 Signing Key [ 1] 2.4.3 O

Table 7b: Key Distribution by Peripheral

Prerequisite: SM 1/2 "Peripheral Role (Responder)"

Item	Capability	Reference	Support	Status	Comment
7b/1	Encryption Key	[ 1] 2.4.3	O
7b/2	Identity Key	[ 1] 2.4.3	O

7b/3 Signing Key [ 1] 2.4.3 O

Table 8a: Cross-Transport Key Derivation by Central

Prerequisite: SM 1/1 "Central Role (Initiator)"

Item	Capability	Reference	Support	Status	Comment
8a/1	Cross Transport Key Derivation Supported	[ 1] 2.3.5.7	C.1		C. 1: Optional IF SM 2/5 "LE Secure Connections", otherwise Excluded.

8a/3 Derivation of BR/EDR Link Key from LE LTK
[ 1] 2.4.2.4 C.2 C.2: Mandatory to support at least one IF SM 8a/1 "Cross Transport Key
Derivation Supported", otherwise Excluded.

Table 8b: Cross-Transport Key Derivation by Peripheral

Prerequisite: SM 1/2 "Peripheral Role (Responder)"

Item	Capability	Reference	Support	Status	Comment
8b/1	Cross Transport Key Derivation Supported	[ 1] 2.3.5.7	C.1		C. 1: Optional IF SM 2/5 "LE Secure Connections", otherwise Excluded.

8b/3 Derivation of BR/EDR Link Key from LE LTK
[ 1] 2.4.2.4 C.2 C.2: Mandatory to support at least one IF SM 8b/1 "Cross Transport Key
Derivation Supported", otherwise Excluded.

Serial Port Profile

Table 0: Major Versions (X.Y)

0/2 SPP v1 .2 SPP v1 .2 C.1 C. 1: Mandatory to support one and only one major version.

Table 1: Role Requirements

Item	Capability	Reference	Support	Status	Comment
1/1	Device A (DevA)	[ 1] 2.2	C.1		C. 1: Mandatory to support at least one of SPP 1/1 "Device A (DevA)" OR SPP 1/2 "Device B (DevB)".

1/2 Device B [ 1] 2.2 C.1 C. 1: Mandatory to support at least one of SPP 1/1 "Device A (DevA)" OR SPP 1/2
(DevB) "Device B (DevB)".

Table 2: Serial Port Service Support

Item	Capability	Reference		Support	Status	Comment
2/1	Support of SPP asa standalone profile	[ 1]	1.2	O
2/1a	SPP as a standalone profileDevice A (DevA)	[ 1]	1.2	C.2, C.3		C.2: Mandatory to support at least one of SPP 2/1a "SPP as a standalone profileDevice A (DevA)" OR SPP 2/1b "SPP as a standalone profile-Device B (DevB)" IF SPP 2/1 "Support of SPP as a standalone profile" is supported, otherwise Excluded. C.3: Optional IF SPP 1/1 "Device A (DevA)" is supported, otherwise Excluded.
2/1b	SPP as a standalone profileDevice B (DevB)	[ 1]	1.2	C.2, C.4		C.2: Mandatory to support at least one of SPP 2/1a "SPP as a standalone profileDevice A (DevA)" OR SPP 2/1b "SPP as a standalone profile-Device B (DevB)" IF SPP 2/1 "Support of SPP as a standalone profile" is supported, otherwise Excluded. C.4: Optional IF SPP 1/2 "Device B (DevB)" is supported, otherwise Excluded.

Table 3: Application Procedures

Item	Capability	Reference	Support	Status	Comment
3/1	Establish link and set up virtual serial connection	[ 1] 3.1	C.1		C. 1: Mandatory IF SPP 1/1 "Device A (DevA)" is supported, otherwise Optional.
3/2	Accept link and virtual serial connection establishment	[ 1] 3.1	C.2		C.2: Mandatory IF SPP 1/2 "Device B (DevB)" is supported, otherwise Optional.

3/3 Register Service record for application [ 1] 3.1 C.3 C.3: Mandatory IF SPP 2/1b "SPP as a standalone profile
in local SDP database Device B (DevB)" is supported, otherwise Optional.

Table 4: SDP Dependencies

Prerequisite: SPP 2/1b "SPP as a standalone profile-Device B (DevB)"

Item	Capability	Reference	Support	Status	Comment
4/1	ServiceClassIDList	[ 1] 6.1	M
4/2	ProtocolDescriptorList	[ 1] 6.1	M

4/6 BluetoothProfileDescriptorList [ 1] 6.1 M

Telephone Bearer Service

Table 0b: Service Requirements

0/1 TBS v1 .0 [ 1] 2.3.1 M

Table 1: Transport Requirements

Prerequisite: TBS 0b/1 "Telephone Bearer Service"

1/2 Service supported over LE [ 1] 1.5 C.1 C. 1: Mandatory to support at least one.

Table 2: Telephone Bearer Service Requirements

Prerequisite: TBS 0b/1 "Telephone Bearer Service"

Item	Capability	Reference	Support	Status Comment
2/1	Telephone Bearer Service	[ 1] 2.3.1	M
2/2	Bearer Provider Name Characteristic	[ 1] 3.1	M
2/4	Bearer UCI Characteristic	[ 1] 3.2	M
2/5	Bearer Technology Characteristic	[ 1] 3.3	M
2/6	Bearer URI Schemes Supported List Characteristic	[ 1] 3.4	M
2/11	Bearer List Current Calls Characteristic	[ 1] 3.7	M
2/13	Content Control ID Characteristic	[ 1] 3.8	M
2/14	Status Flags Characteristic	[ 1] 3.9	M
2/17	Call State Characteristic	[ 1] 3.11	M
2/19	Call Control Point Characteristic	[ 1] 3.12	M
2/20	Call Control Point Optional Opcodes Characteristic	[ 1] 3.13	M
2/21	Termination Reason Characteristic	[ 1] 3.14	M
2/22	Incoming Call Characteristic	[ 1] 3.15	M

Table 3: Call Control Point Opcode Requirements

Prerequisite: TBS 2/19 "Call Control Point Characteristic"

Item	Capability	Reference	Support	Status	Comment
3/1	Accept	[ 1] 3.12.1.1	M
3/2	Terminate	[ 1] 3.12.1.2	M

3/5 Originate [ 1] 3.12.1.5 M
Table 4: GATT Requirements

Item	Capability	Reference		Support	Status	Comment
4/1	Write Characteristic Value	[ 1]	1.4	M
4/2	Write without Response	[ 1]	1.4	M
4/3	Notifications	[ 1]	1.4	M
4/4	Read Characteristic Descriptors	[ 1]	1.4	M

4/5 Write Characteristic Descriptors [ 1] 1.4 M

Table 5: SDP Requirements

Prerequisite: TBS 1/1 "Service supported over BR/EDR"
Item Capability Reference Support Status Comment
Table 20: X.Y Versions
Prerequisite: TBS 0b/2 "Generic Telephone Bearer Service"
Item Capability Reference Support Status Comment
Table 21: Transport Requirements
Prerequisite: TBS 0b/2 "Generic Telephone Bearer Service"
Item Capability Reference Support Status Comment

Table 22: Generic Telephone Bearer Service Requirements

Prerequisite: TBS 0b/2 "Generic Telephone Bearer Service"
Item Capability Reference Support Status Comment
Table 23: Call Control Point Opcode Requirements
Prerequisite: TBS 22/19 "Call Control Point Characteristic"
Item Capability Reference Support Status Comment
Table 24: GATT Requirements
Item Capability Reference Support Status Comment
Table 25: SDP Requirements
Prerequisite: TBS 21/1 "Service supported over BR/EDR"
Item Capability Reference Support Status Comment

Telephony and Media Audio Profile

Table 1: Role Requirements

Item	Capability	Reference	Support	Status	Comment
1/1	Call Gateway (CG)	[2] 3.1	C.1		C. 1: Mandatory to support at least one.
1/2	Call Terminal (CT)	[2] 3.1	C.1		C. 1: Mandatory to support at least one.
1/3	Unicast Media Sender (UMS)	[2] 3.1	C.1		C. 1: Mandatory to support at least one.

1/4	Unicast Media Receiver (UMR)	[2] 3.1	C.1		C. 1: Mandatory to support at least one.
1/6	Broadcast Media Receiver (BMR)	[2] 3.1	C. 1, C.2		C. 1: Mandatory to support at least one. C.2: Mandatory IF TMAP 1/4 "Unicast Media Receiver (UMR)", otherwise Optional.
1/7	TMA Client	[2] 3.8	O

1/8 TMA Server [2] 3.8 C.3 C.3: Excluded IF TMAP 1/5 "Broadcast Media Sender (BMS)"AND NOT GATT
1/2 "Generic Attribute Profile (GATT) Server", otherwise Mandatory.

Table 2: Transport Requirements

2/2 Profile supported over LE [2] 4.3 M

Table 3: Device Configuration Requirements

3/2 BR/EDR/LE [2] 4.9 C.1 C. 1: Mandatory to support one and only one.
Table 10: X.Y Versions
Prerequisite: TMAP 1/1 "Call Gateway (CG)"

10/1 TMAP v1 .0 [2] M

Table 12: Call Gateway Profile and Service Dependencies

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status	Comment
12/1	Common Audio Profile	[2] 3.1	M
12/2	Basic Audio Profile	[2] 3.1	M
12/3	Call Control Profile	[2] 3.1	M

Table 13: Role Discovery Requirements

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

13/1 Advertise Call Gateway Support [2] 3.4 O

Table 14: CG Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status	Comment
14/1	CAP Initiator	[2] 3.1	M
14/2	CAP Commander	[2] 3.1	M
14/3	CCP Call Control Server	[2] 3.1	M
14/4	VCP Volume Controller	[2] 3.1	M
14/5	Audio Source	[2] 3.1	M

14/6 Audio Sink [2] 3.1 M

Table 15: Call Gateway Config Codec Operation Parameters

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status	Comment
15/3	32_2 LC3: 32 kHz Sampling Frequency, 10 ms Frame Duration, 80 Octets (Audio Source)	[2] 3.5.1.4.1	M

15/6 32_2 LC3: 32 kHz Sampling Frequency, 10 ms Frame Duration, 80 Octets (Audio Sink) [2] 3.5.1.4.1 M

Table 16: Call Gateway QoS Settings Requirements

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status	Comment
16/3	32_2_ 1 LC3: 10000 SDU Interval, unframed, 80 Max SDU Size, 2 RTN, 10 Max_Transport_Latency (Audio Source)	[2] 3.5.1.4.2	M

16/6 32_2_ 1 LC3: 10000 SDU Interval, unframed, 80 Max SDU Size, 2 RTN, 10 Max_Transport_Latency (Audio Sink)
[2] 3.5.1.4.2
M

Table 17: Number of Concurrent Unicast Audio Streams, Channels, and Devices

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status	Comment
17/1	Configuration A: 1 bidirectional stream between CG and CT	[2] 3.5.1.5	M
17/2	Configuration B: 1 stream with 1 channel from CG to CT, 1 stream with 1 channel from 2nd CT to CG.	[2] 3.5.1.5	M
17/3	Configuration C: 1 stream with 1 channel from CG to CT, 1 bidirectional stream between CG and a 2nd CT	[2] 3.5.1.5	M

17/4 Configuration D: 1 stream with 1 channel from CG to CT, 1 bidirectional stream between CG [2] 3.5.1.5 M
and same CT

Table 18: Call Gateway PACS Characteristic Support Requirements

Prerequisite: TMAP 1/1 "Call Gateway (CG)"

Item	Capability	Reference	Support	Status	Comment
18/1	Sink Audio Locations characteristic	[2] 3.5.1.2	M

18/2 Source Audio Locations characteristic [2] 3.5.1.2 M

Table 19: Call Gateway Audio Channel Allocation Audio Location Values

Prerequisite: TMAP 1/1 "Call Gateway (CG)"
Item Capability Reference Support Status Comment
Table 20: Call Gateway Audio Input Features
Prerequisite: TMAP 1/1 "Call Gateway (CG)"
Item Capability Reference Support Status Comment
Table 30: X.Y Versions
Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

30/1 TMAP v1 .0 [2] M

Table 32: UMS Profile and Service Dependencies

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status	Comment
32/1	Common Audio Profile	[2] 3.1	M
32/2	Basic Audio Profile	[2] 3.1	M

32/3 Media Control Profile [2] 3.1 M

Table 33: Role Discovery Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

33/1 Advertise Unicast Media Sender Support [2] 3.4 O

Table 34: UMS Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status	Comment
34/1	CAP Initiator	[2] 3.1	M
34/2	CAP Commander	[2] 3.1	M
34/3	MCP Media Control Server	[2] 3.1	M
34/4	VCP Volume Controller	[2] 3.1	M
34/5	Audio Source	[2] 3.1	M

Table 35: Unicast Media Sender Config Codec Operation Parameters

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status	Comment
35/2	48_2 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 100 Octets	[2] 3.5.1.4.1	M
35/4	48_4 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 120 Octets	[2] 3.5.1.4.1	C.1		C. 1: Mandatory to support at least one.

35/6 48_6 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 155 Octets
[2] 3.5.1.4.1
C.1 C. 1: Mandatory to support at least one.

Table 36: Unicast Media Sender QoS Settings Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status	Comment
36/2	48_2_ 1 LC3: 10000 SDU Interval, unframed, 100 Max SDU Size, 5 RTN, 20 Max_Transport_Latency	[2] 3.5.1.4.2	M
36/4	48_4_ 1 LC3: 10000 SDU Interval, unframed, 120	[2]	C.3		C.3: Mandatory IF TMAP 35/4 "48_4 LC3: 48 kHz
	Max SDU Size, 5 RTN, 20	3.5.1.4.2			Sampling Frequency, 10 ms Frame Duration, 120
	Max_Transport_Latency				Octets", otherwise not defined.
36/6	48_6_ 1 LC3: 10000 SDU Interval, unframed, 155	[2]	C.5		C.5: Mandatory IF TMAP 35/6 "48_6 LC3: 48 kHz
	Max SDU Size, 5 RTN, 20	3.5.1.4.2			Sampling Frequency, 10 ms Frame Duration, 155
	Max_Transport_Latency				Octets", otherwise not defined.

36/10	48_2_2 LC3: 10000 SDU Interval, unframed, 100 Max SDU Size, 13 RTN, 95 Max_Transport_Latency	[2] 3.5.1.4.2	M
36/12	48_4_2 LC3: 10000 SDU Interval, unframed, 120 Max SDU Size, 13 RTN, 100 Max_Transport_Latency	[2] 3.5.1.4.2	C.3		C.3: Mandatory IF TMAP 35/4 "48_4 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 120 Octets", otherwise not defined.
36/14	48_6_2 LC3: 10000 SDU Interval, unframed, 155 Max SDU Size, 13 RTN, 100 Max_Transport_Latency	[2] 3.5.1.4.2	C.5	C.5: Mandatory IF TMAP 35/6 "48_6 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 155 Octets", otherwise not defined.

Table 37: Unicast Media Sender PACS Characteristic Support Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

37/1 Sink Audio Locations characteristic [2] 3.5.1.2 M

Table 38: Unicast Media Sender Audio Channel Allocation Audio Location Values

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status	Comment
38/1	Front Left Audio Location	[2] 3.5.1.4.1	M
38/2	Front Right Audio Location	[2] 3.5.1.4.1	M

Table 39: Unicast Media Sender BAP Audio Configuration

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"
Item Capability Reference Support Status Comment
Table 40: GMCS Generic Media Control Point Opcodes
Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"

Item	Capability	Reference	Support	Status	Comment
40/1	Play	[2] 3.6.1	M

40/2 Pause [2] 3.6.1 M
Table 41: Call Gateway Audio Input Features
Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)"
Item Capability Reference Support Status Comment
Table 50: X.Y Versions
Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment
Table 52: BMS Profile and Service Dependencies
Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment
Table 53: Role Discovery Requirements
Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)" AND TMAP 1/8 "TMA Server"
Item Capability Reference Support Status Comment
Table 54: BMS Inter-Layer Dependency Role Requirements
Item Capability Reference Support Status Comment
Table 55: Broadcast Media Sender Codec Settings Requirements
Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment

Table 56: Broadcast Media Sender QoS Settings Requirements

Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment
Table 57: Broadcast Media Sender Audio Channel Allocation Audio Location Values
Prerequisite: TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment
Table 70: X.Y Versions
Prerequisite: TMAP 1/2 "Call Terminal (CT)"

70/1 TMAP v1 .0 [2] M

Table 72: CT Profile and Service Dependencies

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

Item	Capability	Reference	Support	Status	Comment
72/1	Common Audio Profile	[2] 3.1	M
72/2	Basic Audio Profile	[2] 3.1	M

Table 73: Role Discovery Requirements

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

73/1 Advertise Call Terminal Support [2] 3.4 O

Table 74: CT Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

Item	Capability	Reference	Support	Status	Comment
74/1	CAP Acceptor	[2] 3.1	M
74/2	CAP Commander	[2] 3.1	O
74/3	VCP Volume Renderer	[2] 3.1	C.1		C. 1: Mandatory IF TMAP 74/4 "BAP Audio Sink", otherwise not defined.
74/4	BAP Audio Sink	[2] 3.1	C.2		C.2: Mandatory to support at least one.
74/5	BAP Audio Source	[2] 3.1	C.2		C.2: Mandatory to support at least one.

Table 75: Call Terminal PAC Records

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

Item	Capability	Reference	Support	Status	Comment
75/1	16_ 1 LC3: 16 kHz Sampling Frequency, 7.5 ms Frame Duration, 30 Octets (Audio Sink)	[2] 3.5.1.1	C.1		C. 1: Mandatory IF TMAP 74/4 "BAP Audio Sink", otherwise not defined.

75/2	32_ 1 LC3: 32 kHz Sampling Frequency, 7.5 ms Frame Duration, 60 Octets (Audio Sink)	[2] 3.5.1.1	C.1		C. 1: Mandatory IF TMAP 74/4 "BAP Audio Sink", otherwise not defined.
75/3	32_2 LC3: 32 kHz Sampling Frequency, 10 ms Frame Duration, 80 Octets (Audio Sink)	[2] 3.5.1.1	C.1		C. 1: Mandatory IF TMAP 74/4 "BAP Audio Sink", otherwise not defined.
75/4	16_ 1 LC3: 16 kHz Sampling Frequency, 7.5 ms Frame Duration, 30 Octets (Audio Source)	[2] 3.5.1.1	C.2		C.2: Mandatory IF TMAP 74/5 "BAP Audio Source", otherwise not defined.
75/5	32_ 1 LC3: 32 kHz Sampling Frequency, 7.5 ms Frame Duration, 60 Octets (Audio Source)	[2] 3.5.1.1	C.2		C.2: Mandatory IF TMAP 74/5 "BAP Audio Source", otherwise not defined.
75/6 32_2 LC3: 32 kHz Sampling Frequency, 10 ms Frame Duration, 80 Octets (Audio Source)		[2] 3.5.1.1	C.2	C.2: Mandatory IF TMAP 74/5 "BAP Audio Source", otherwise not defined.

Table 76: Call Terminal QoS Settings Requirements

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

Item	Capability	Reference	Support	Status	Comment
76/1	16_ 1_ 1 LC3: 7500 SDU Interval, unframed, 30 Max SDU Size, 2	[2]	C.1		C. 1: Mandatory IF TMAP 74/4 "BAP
	RTN, 8 Max_Transport_Latency (Audio Sink)	3.5.1.4.2			Audio Sink", otherwise not defined.
76/2	32_ 1_ 1 LC3: 7500 SDU Interval, unframed, 60 Max SDU Size, 2	[2]	C.1		C. 1: Mandatory IF TMAP 74/4 "BAP
	RTN, 8 Max_Transport_Latency (Audio Sink)	3.5.1.4.2			Audio Sink", otherwise not defined.
76/3	32_2_ 1 LC3: 10000 SDU Interval, unframed, 80 Max SDU Size,	[2]	C.1		C. 1: Mandatory IF TMAP 74/4 "BAP
	2 RTN, 10 Max_Transport_Latency (Audio Sink)	3.5.1.4.2			Audio Sink", otherwise not defined.
76/4	16_ 1_ 1 LC3: 7500 SDU Interval, unframed, 30 Max SDU Size, 2	[2]	C.2		C.2: Mandatory IF TMAP 74/5 "BAP
	RTN, 8 Max_Transport_Latency (Audio Source)	3.5.1.4.2			Audio Source", otherwise not defined.
76/5	32_ 1_ 1 LC3: 7500 SDU Interval, unframed, 60 Max SDU Size, 2	[2]	C.2		C.2: Mandatory IF TMAP 74/5 "BAP
	RTN, 8 Max_Transport_Latency (Audio Source)	3.5.1.4.2			Audio Source", otherwise not defined.
76/6	32_2_ 1 LC3: 10000 SDU Interval, unframed, 80 Max SDU Size,	[2]	C.2		C.2: Mandatory IF TMAP 74/5 "BAP
	2 RTN, 10 Max_Transport_Latency (Audio Source)	3.5.1.4.2			Audio Source", otherwise not defined.

Table 77: Number of Audio Outputs

Prerequisite: TMAP 1/2 "Call Terminal (CT)"

77/1 1 audio output [2] 3.5.1.5 M
Table 78: Number of Concurrent Unicast Audio Streams, Channels, and Devices
Prerequisite: TMAP 1/2 "Call Terminal (CT)"
Item Capability Reference Support Status Comment
Table 79: Call Terminal Multi-Stream Configurations
Prerequisite: TMAP 1/2 "Call Terminal (CT)"

79/1 Case 1: Multiple CT audio sink devices each with a single ASE [2] 3.7 C.1 C. 1: Mandatory to support at least one.

Table 90: X.Y Versions

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

90/1 TMAP v1 .0 [2] M
Table 92: UMR Profile and Service Dependencies

Item	Capability	Reference	Support	Status	Comment
92/1	Common Audio Profile	[2] 3.1	M
92/2	Basic Audio Profile	[2] 3.1	M

Table 93: Role Discovery Requirements

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

93/1 Advertise Unicast Media Receiver Support [2] 3.4 O

Table 94: UMR Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support	Status	Comment
94/1	CAP Acceptor	[2] 3.1	M
94/2	CAP Commander	[2] 3.1	O
94/3	VCP Volume Renderer	[2] 3.1	M
94/4	BAP Audio Sink	[2] 3.1	M

Table 95: Unicast Media Receiver PAC Records

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support	Status Comment
95/1	48_ 1 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 75 Octets	[2] 3.5.1.1	M
95/2	48_2 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 100 Octets	[2] 3.5.1.1	M
95/3	48_3 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 90 Octets	[2] 3.5.1.1	M
95/4	48_4 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 120 Octets	[2] 3.5.1.1	M
95/5	48_5 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 117 Octets	[2] 3.5.1.1	M
95/6	48_6 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 155 Octets	[2] 3.5.1.1	M

Table 96: Unicast Media Receiver QoS Settings Requirements

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support	Status Comment
96/1	48_ 1_ 1 LC3: 7500 SDU Interval, unframed, 75 Max SDU Size, 5 RTN, 15 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/2	48_2_ 1 LC3: 10000 SDU Interval, unframed, 100 Max SDU Size, 5 RTN, 20 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/3	48_3_ 1 LC3: 7500 SDU Interval, unframed, 90 Max SDU Size, 5 RTN, 15 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/4	48_4_ 1 LC3: 10000 SDU Interval, unframed, 120 Max SDU Size, 5 RTN, 20 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/5	48_5_ 1 LC3: 7500 SDU Interval, unframed, 117 Max SDU Size, 5 RTN, 15 Max_Transport_Latency	[2] 3.5.1.4.2	M

96/6	48_6_ 1 LC3: 10000 SDU Interval, unframed, 155 Max SDU Size, 5 RTN, 20 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/9	48_ 1_2 LC3: 7500 SDU Interval, unframed, 75 Max SDU Size, 13 RTN, 75 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/10	48_2_2 LC3: 10000 SDU Interval, unframed, 100 Max SDU Size, 13 RTN, 95 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/11	48_3_2 LC3: 7500 SDU Interval, unframed, 90 Max SDU Size, 13 RTN, 75 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/12	48_4_2 LC3: 10000 SDU Interval, unframed, 120 Max SDU Size, 13 RTN, 100 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/13	48_5_2 LC3: 7500 SDU Interval, unframed, 117 Max SDU Size, 13 RTN, 75 Max_Transport_Latency	[2] 3.5.1.4.2	M
96/14	48_6_2 LC3: 10000 SDU Interval, unframed, 155 Max SDU Size, 13 RTN, 100 Max_Transport_Latency	[2] 3.5.1.4.2	M

Table 97: Unicast Media Receiver PACS Characteristic Support Requirements

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

97/1 Sink Audio Locations characteristic [2] M

Table 98: Unicast Media Receiver Sink Audio Locations Values

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

Item	Capability	Reference	Support	Status	Comment
98/1	Front Left Sink Audio Location	[2] 3.5.1.2.1	C.1		C. 1: Mandatory to support at least one.
98/2	Front Right Sink Audio Location	[2] 3.5.1.2.1	C.1		C. 1: Mandatory to support at least one.

98/3 Front Right and Front Left Sink Audio Locations [2] 3.5.1.2.1 C.1 C. 1: Mandatory to support at least one.

Table 99: Number of Audio Outputs

Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

99/1 1 audio output [2] 3.7 M
Table 100: Unicast Media Receiver Multi-Stream Configurations
Prerequisite: TMAP 1/4 "Unicast Media Receiver (UMR)"

100/1 Case 1: Multiple UMR audio sink devices each with a single [2] 3.7 C.1 C. 1: Mandatory to support at least
ASE one.

Table 110: X.Y Versions

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

110/1 TMAP v1 .0 [2] M
Table 112: BMR Profile and Service Dependencies
Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"
Table 113: Role Discovery Requirements

Item Capability Reference Support Status Comment
112/1 Common Audio Profile	[2] 3.1	M
112/2 Basic Audio Profile Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"	[2] 3.1	M
Item Capability		Reference	Support	Status Comment

113/1 Advertise Broadcast Media Receiver Support [2] 3.4 O

Table 114: BMR Inter-Layer Dependency Role Requirements

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status	Comment
114/1	CAP Acceptor	[2] 3.1	M
114/3	VCP Volume Renderer	[2] 3.1	M

114/4 BAP Broadcast Sink [2] 3.1 M

Table 115: Broadcast Media Receiver Codec Settings Requirements

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status Comment
115/1	48_ 1 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 75 Octets	[2] 3.5.2.1	M
115/2	48_2 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 100 Octets	[2] 3.5.2.1	M
115/3	48_3 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 90 Octets	[2] 3.5.2.1	M
115/4	48_4 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 120 Octets	[2] 3.5.2.1	M
115/5	48_5 LC3: 48 kHz Sampling Frequency, 7.5 ms Frame Duration, 117 Octets	[2] 3.5.2.1	M

115/6 48_6 LC3: 48 kHz Sampling Frequency, 10 ms Frame Duration, 155 Octets [2] 3.5.2.1 M

Table 116: Broadcast Media Receiver QoS Settings Requirements

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status Comment
116/1	48_ 1_ 1 LC3: 7500 SDU Interval, unframed, 75 Max SDU Size, 4 RTN, 15 Max_Transport_Latency	[2] 3.5.2.3	M
116/2	48_2_ 1 LC3: 10000 SDU Interval, unframed, 100 Max SDU Size, 4 RTN, 20 Max_Transport_Latency	[2] 3.5.2.3	M
116/3	48_3_ 1 LC3: 7500 SDU Interval, unframed, 90 Max SDU Size, 4 RTN, 15 Max_Transport_Latency	[2] 3.5.2.3	M
116/4	48_4_ 1 LC3: 10000 SDU Interval, unframed, 120 Max SDU Size, 4 RTN, 20 Max_Transport_Latency	[2] 3.5.2.3	M
116/5	48_5_ 1 LC3: 7500 SDU Interval, unframed, 117 Max SDU Size, 4 RTN, 15 Max_Transport_Latency	[2] 3.5.2.3	M
116/6	48_6_ 1 LC3: 10000 SDU Interval, unframed, 155 Max SDU Size, 4 RTN, 20 Max_Transport_Latency	[2] 3.5.2.3	M
116/9	48_ 1_2 LC3: 7500 SDU Interval, unframed, 75 Max SDU Size, 4 RTN, 50 Max_Transport_Latency	[2] 3.5.2.3	M

116/10	48_2_2 LC3: 10000 SDU Interval, unframed, 100 Max SDU Size, 4 RTN, 65 Max_Transport_Latency	[2] 3.5.2.3	M
116/11	48_3_2 LC3: 7500 SDU Interval, unframed, 90 Max SDU Size, 4 RTN, 50 Max_Transport_Latency	[2] 3.5.2.3	M
116/12	48_4_2 LC3: 10000 SDU Interval, unframed, 120 Max SDU Size, 4 RTN, 65 Max_Transport_Latency	[2] 3.5.2.3	M
116/13	48_5_2 LC3: 7500 SDU Interval, unframed, 117 Max SDU Size, 4 RTN, 50 Max_Transport_Latency	[2] 3.5.2.3	M
116/14	48_6_2 LC3: 10000 SDU Interval, unframed, 155 Max SDU Size, 4 RTN, 65 Max_Transport_Latency	[2] 3.5.2.3	M

Table 117: BMR Codec Specific Audio Capability Support

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status	Comment
117/1	Multiple Audio Locations	[2] 3.5.2.	O

117/2 Two Audio Channels [2] 3.5.2 O

Table 118: BMR Audio Location Values

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

Item	Capability	Reference	Support	Status	Comment
118/1	Front Left Audio Location	[2] 3.5.2.2	C.1		C. 1: Mandatory to support at least one.
118/2	Front Right Audio Location	[2] 3.5.2.2	C.1		C. 1: Mandatory to support at least one.

118/3 Front Right and Front Left Audio Locations [2] 3.5.2.2 C.1 C. 1: Mandatory to support at least one.

Table 119: Number of Audio Outputs

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

119/1 1 audio output [2] 3.7 M

Table 120: LC3 Audio Configuration

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

120/1
AC14: 1 BIS, Multiple Audio Channels/BIS, 1 Audio Stream
[2]
C.1
C. 1: Mandatory IF TMAP 117/1 "Multiple Audio Locations" AND TMAP 117/2 "Two Audio Channels", otherwise not defined.

Table 121: Multi-Stream Configurations

Prerequisite: TMAP 1/6 "Broadcast Media Receiver (BMR)"

121/1 Case 5: Multiple BMR devices, each synchronized to a single [2] 3.7 C.1 C. 1: Mandatory to support at least
BIS one.

Table 130: CAP Procedure Requirements

Prerequisite: TMAP 1/3 "Unicast Media Sender (UMS)" AND TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment
Table 131: Link Layer and HCI Features
Prerequisite: TMAP 1/1 "Call Gateway (CG)" OR TMAP 1/2 "Call Terminal (CT)" OR TMAP 1/3 "Unicast Media Sender (UMS)" OR TMAP 1/4 "Unicast Media Receiver (UMR)" OR TMAP 1/5 "Broadcast Media Sender (BMS)" OR TMAP 1/6 "Broadcast Media Receiver (BMR)"

131/1 LE 2M PHY [2] 3.2 M

Table 140: MCS Media Control Point Opcodes

Prerequisite: TMAP 1/1 "Call Gateway (CG)" OR TMAP 1/3 "Unicast Media Sender (UMS)" OR TMAP 1/5 "Broadcast Media Sender (BMS)"
Item Capability Reference Support Status Comment
140/1 Play [2] 3.6.1 C.1 C.1: Mandatory IF TMAP 140/3 "Media Control Service", otherwise not defined. 140/2 Pause [2] 3.6.1 C.1 C. 1: Mandatory IF TMAP 140/3 "Media Control Service", otherwise not defined.
Table 150: TMA Service Characteristic Support Requirements
Prerequisite: TMAP 1/7 "TMA Client"

150/1 TMAP Role Characteristic [2] 4.7.1 M

Table 151: GATT Requirements

Prerequisite: TMAP 1/7 "TMA Client"

Item	Capability	Reference	Support	Status	Comment
151/1	GATT Client over LE	[2] 3.8	M
151/2	Discover All Primary Services	[2] 3.8.1.3	C.1		C. 1: Mandatory to support at least one.
151/3	Discover Primary Services by Service UUID	[2] 3.8.1.3	C.1		C. 1: Mandatory to support at least one.
151/4	Discover All Characteristics of a Service	[2] 3.8.1.3	C.2		C.2: Mandatory to support at least one.
151/5	Discover Characteristics by UUID	[2] 3.8.1.3	C.2		C.2: Mandatory to support at least one.

151/6 Read Characteristic Value [2] 3.8.1.3 M

Table 152: Service Characteristic

Prerequisite: TMAP 1/8 "TMA Server"

152/1 TMAP Role Characteristic [2] 4.7.1 M

Table 153: TMAP Role Support

Prerequisite: TMAP 152/1 "TMAP Role Characteristic"

Item	Capability	Reference	Support	Status	Comment
153/1	Call Gateway Support	[2] 4.7.1.2	C.1		C. 1: Mandatory IF TMAP 1/1 "Call Gateway (CG)", otherwise Excluded.
153/2	Call Terminal Support	[2] 4.7.1.2	C.2		C.2: Mandatory IF TMAP 1/2 "Call Terminal (CT)", otherwise Excluded.
153/3	Unicast Media Sender Support	[2] 4.7.1.2	C.3		C.3: Mandatory IF TMAP 1/3 "Unicast Media Sender (UMS)", otherwise Excluded.
153/4	Unicast Media Receiver Support	[2] 4.7.1.2	C.4		C.4: Mandatory IF TMAP 1/4 "Unicast Media Receiver (UMR)", otherwise Excluded.

153/6 Broadcast Media Receiver [2] 4.7.1.2 C.6 C.6: Mandatory IF TMAP 1/6 "Broadcast Media Receiver (BMR)",
Support otherwise Excluded.

Table 154: GATT Requirements

Prerequisite: TMAP 1/8 "TMA Server"

154/1 GATT Server over LE [2] 4.8 M

Table 155: SDP Requirements

Prerequisite: TMAP 1/8 "TMA Server"AND TMAP 2/1 "Profile supported over BR/EDR"
Item Capability Reference Support Status Comment

Table 156: GAP Requirements

Prerequisite: TMAP 1/7 "TMA Client" OR TMAP 1/8 "TMA Server"

156/1 LE security mode 1 [2] 4.8 M

Volume Control Profile

Table 1: Role Requirements

Item	Capability	Reference	Support	Status	Comment
1/1	Volume Renderer	[ 1] 3.0	C.1		C. 1: Mandatory to support at least one.
1/2	Volume Controller	[ 1] 4.0	C.1		C. 1: Mandatory to support at least one.

Table 2: Transport Requirements

2/2 Profile supported over LE [ 1] 2.4 C.1 C. 1: Mandatory to support at least one.

Table 3: Volume Renderer, X.Y Versions

Prerequisite: VCP 1/1 "Volume Renderer"

3/1 Volume Control Profile 1.0 [ 1] M

Table 5: Service Requirements

Prerequisite: VCP 1/1 "Volume Renderer"

Item	Capability	Reference	Support	Status	Comment
5/1	Volume Control Service	[ 1] 3.0	M
5/4	LE Extended Advertising	[ 1] 6.1.1.1	M

Table 6: GAP Requirements-Volume Renderer Role

Prerequisite: VCP 1/1 "Volume Renderer"

Item	Capability	Reference	Support	Status	Comment
6/1	LE security mode 1	[ 1] 5.1	C.1		C. 1: Mandatory IF VCP 2/2 "Profile supported over LE", otherwise not defined.
6/2	Unauthenticated Pairing (LE security mode 1 level 2) with LE Secure Connections Pairing only	[ 1] 5.1	C.1		C. 1: Mandatory IF VCP 2/2 "Profile supported over LE", otherwise not defined.

6/3	Authenticated Pairing (LE security mode 1 level 3) with LE Secure Connections Pairing only	[ 1] 5.1	C.3		C.3: Optional IF VCP 2/2 "Profile supported over LE", otherwise not defined.
6/8	Minimum 128 Bit entropy key (LE)	[ 1] 5.1	C.1		C. 1: Mandatory IF VCP 2/2 "Profile supported over LE", otherwise not defined.
6/10	LE Secure Connections (Peripheral)	[ 1] 5.1	C.6		C.6: Mandatory to support at least one IF VCP 2/2 "Profile supported over LE", otherwise not defined.

6/13 Peripheral [ 1] 4.1 C.1 C. 1: Mandatory IF VCP 2/2 "Profile supported over
LE", otherwise not defined.

Table 8: Volume Controller, X.Y Versions

Prerequisite: VCP 1/2 "Volume Controller"

8/1 Volume Control Profile 1.0 [ 1] M

Table 10: Volume Control Service Support

Prerequisite: VCP 1/2 "Volume Controller"

10/1 Discover Volume Control Service [ 1] 4.0 M
Table 11: Volume Control Service Characteristic Support Requirements
Prerequisite: VCP 10/1 "Discover Volume Control Service"

Item	Capability	Reference	Support	Status	Comment
11/1	Volume State	[ 1] 4.3.1	M

11/2 Volume Control Point [ 1] 4.3.1 M

Table 12: Volume Control Service Procedure Support Requirements

Prerequisite: VCP 10/1 "Discover Volume Control Service"

Item	Capability	Reference	Support	Status	Comment
12/1	Configure Volume State Notifications	[ 1] 4.4. 1, 4.4.1.1	M
12/2	Read Volume State	[ 1] 4.4. 1, 4.4.1.2	M
12/6	Set Absolute Volume	[ 1] 4.4. 1, 4.4.1.6.5	C.2		C.2: Mandatory IF NOT VCP 12/7 "Relative Volume Down"AND NOT VCP 12/8 "Relative Volume Up"AND NOT VCP 12/9 "Unmute/ Relative Volume Down"AND NOT VCP 12/10 "Unmute/ Relative Volume Up", otherwise Optional.
12/11	Mute	[ 1] 4.4. 1, 4.4.1.6.6	O

12/12 Unmute [ 1] 4.4. 1, O
4.4.1.6.7

Table 13: Volume Offset Control Service Characteristic Support Requirements

Prerequisite: VCP 10/2 "Discover Volume Offset Control Service"
Item Capability Reference Support Status Comment
Table 14: Volume Offset Control Service Procedure Support Requirements
Prerequisite: VCP 10/2 "Discover Volume Offset Control Service"
Table 15: Audio Input Control Service Characteristic Support Requirements
Item Capability Reference Support Status Comment
Prerequisite: VCP 10/3 "Discover Audio Input Control Service"
Item Capability Reference Support Status Comment

Table 16: Audio Input Control Service Procedure Support Requirements

Prerequisite: VCP 10/3 "Discover Audio Input Control Service"
Item Capability Reference Support Status Comment

Table 17: Volume Controller GATT Requirements

Prerequisite: VCP 1/2 "Volume Controller"

Item	Capability	Reference	Support	Status	Comment
17/1	Discover All Primary Services	[ 1] 4.1	C.1		C. 1: Mandatory to support at least one.
17/2	Discover Primary Services by Service UUID	[ 1] 4.1	C.1		C. 1: Mandatory to support at least one.
17/3	Find Included Services	[ 1] 4.1	O
17/4	Discover All Characteristics of a Service	[ 1] 4.1	C.2		C.2: Mandatory to support at least one.
17/5	Discover Characteristics by UUID	[ 1] 4.1	C.2		C.2: Mandatory to support at least one.
17/6	Discover All Characteristic Descriptors	[ 1] 4.1	M
17/7	Read Characteristic Value	[ 1] 4.1	M
17/8	Write Characteristic Value	[ 1] 4.1	M
17/9	Notifications	[ 1] 4.1	M
17/10	Read Characteristic Descriptors	[ 1] 4.1	M

17/11 Write Characteristic Descriptors [ 1] 4.1 M

Table 18: GAP Requirements-Volume Controller Role

Prerequisite: VCP 1/2 "Volume Controller"

Volume Control Service

Table 0: X.Y Versions
Table 0a: X.Y.Z Versions
Table 1: Transport Requirements
Table 2: Volume Control Service
Table 3: Volume Control Point Procedure Requirements
Prerequisite: VCS 2/2 "Volume Control Point Characteristic"
Table 4: GATT Requirements
Table 5: SDP Requirements
Prerequisite: VCS 1/1 "Service supported over BR/EDR"

Item	Capability	Reference Support Status	Comment
18/1	Central	[ 1] 4.1 C.2	C.2: Mandatory IF VCP 2/2 "Profile supported over LE", otherwise not defined.
18/2	LE security mode 1	[ 1] 5.1 C.2	C.2: Mandatory IF VCP 2/2 "Profile supported over LE", otherwise not defined.
18/3	Bondable mode (LE)	[ 1] 6.2 C.2	C.2: Mandatory IF VCP 2/2 "Profile supported over LE", otherwise not defined.
18/4	Bonding procedure	[ 1] 6.2 C.3	C.3: Optional IF VCP 2/2 "Profile supported over LE", otherwise not defined.
18/6	Unauthenticated Pairing (LE security mode 1 level 2) with LE Secure Connections Pairing only	[ 1] 5.1 C.2	C.2: Mandatory IF VCP 2/2 "Profile supported over LE", otherwise not defined.
18/7	Authenticated Pairing (LE security mode 1 level 3) with LE Secure Connections Pairing only	[ 1] 5.1 C.3	C.3: Optional IF VCP 2/2 "Profile supported over LE", otherwise not defined.
18/12	Minimum 128 Bit entropy key (LE)	[ 1] 5.1 C.2	C.2: Mandatory IF VCP 2/2 "Profile supported over LE", otherwise not defined.
18/14	LE Secure Connections (Central)	[ 1] 5.1 C.7	C.7: Mandatory to support at least one IF VCP 2/2 "Profile supported over LE", otherwise not defined.
Item	Capability Reference	Support	Status Comment
0/1	VCS v1 .0 [ 1]	M
Item	Capability Reference	Support	Status Comment
0a/1	VCS v1 .0.1 [3]	O
Item	Capability Reference	Support Status	Comment
1/2	Service supported over LE [ 1] 1.5	C.1	C. 1: Mandatory to support at least one.
Item	Capability	Reference	Support Status Comment
2/1	Volume State Characteristic	[ 1] 3.1	M
2/2	Volume Control Point Characteristic	[ 1] 3.2	M
2/3	Volume Flags Characteristic	[ 1] 3.3	M
Item	Capability	Reference	Support Status Comment
3/1	Relative Volume Down Procedure	[ 1] 3.2.2.1	M
3/2	Relative Volume Up Procedure	[ 1] 3.2.2.2	M
3/3	Unmute / Relative Volume Down Procedure	[ 1] 3.2.2.3	M
3/4	Unmute / Relative Volume Up Procedure	[ 1] 3.2.2.4	M
3/5	Set Absolute Volume Procedure	[ 1] 3.2.2.5	M
3/6	Unmute Procedure	[ 1] 3.2.2.6	M

3/7 Mute Procedure [ 1] 3.2.2.7 M

Item	Capability	Reference		Support	Status	Comment
4/1	Write Characteristic Value	[ 1]	1.4	M
4/2	Notifications	[ 1]	1.4	M
4/3	Read Characteristic Descriptors	[ 1]	1.4	M
4/4	Write Characteristic Descriptors	[ 1]	1.4	M
4/6	GATT Server over LE	[ 1]	1.4	C.2		C.2: Mandatory IF VCS 1/2 "Service supported over LE", otherwise not defined.

Item Capability Reference Support Status Comment
olume fset
V Of Control Service

Table 0: X.Y Versions

Item Capability	Reference	Support	Status	Comment
0/1 VOCS v1 .0 Table 0a: X.Y.Z Versions	[ 1]	M
Item Capability	Reference	Support	Status	Comment

0a/1 VOCS v1 .0.1 [3] O

Table 1: Transport Requirements

1/2 Service supported over LE [ 1] 1.5 C.1 C. 1: Mandatory to support at least one.

Table 2: Volume Offset Control Service

Item	Capability	Reference	Support	Status	Comment
2/1	Volume Offset State Characteristic	[ 1] 3.1	M
2/2	Audio Location Characteristic	[ 1] 3.2	M
2/3	Volume Offset Control Point	[ 1] 3.3	M
2/4	Audio Output Description Characteristic	[ 1] 3.4	M

Table 3: GATT Requirements

Item	Capability	Reference		Support	Status	Comment
3/1	Write Characteristic Value	[ 1]	1.4	M
3/2	Notifications	[ 1]	1.4	M

3/3	Read Characteristic Descriptors	[ 1] 1.4		M
3/4	Write Characteristic Descriptors	[ 1]	1.4	M
3/6	GATT Server over LE	[ 1]	1.4	C.2		C.2: Mandatory IF VOCS 1/2 "Service supported over LE", otherwise not defined.

Table 4: SDP Requirements

Prerequisite: VOCS 1/1 "Service supported over BR/EDR"
Item Capability Reference Support Status Comment